Netgear DG834 DG834v3 Reference Manual - Page 80

How to Set Up a Client-to-Gateway VPN Configuration

Get Netgear DG834 - ADSL Firewall Router PDF manuals and user guides
UPC - 606449029109
View all Netgear DG834 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Reference Manual for the ADSL Modem Router DG834 v3 How to Set Up a Client-to-Gateway VPN Configuration Setting up a VPN between a remote PC running the NETGEAR ProSafe VPN Client and a network gateway (see Figure 6-3) involves the following two steps: • "Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834 v3" on page 6-6 uses the VPN Wizard to configure the VPN tunnel between the remote PC and network gateway. • "Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC" on page 6-11 configures the NETGEAR ProSafe VPN Client endpoint. 22.23.24.25 DG834 192.168.3.1 PCs Figure 6-3 VPN Tunnel 0.0.0.0 PC (Running NETGEAR ProSafe VPN Client) Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834 v3 Note: This section uses the VPN Wizard to set up the VPN tunnel using the VPNC default parameters listed in Table 6-2 on page 6-4. If you have special requirements not covered by these VPNC-recommended parameters, refer to "How to Set Up VPN Tunnels in Special Circumstances" on page 6-36 to set up the VPN tunnel. The worksheet below identifies the parameters used in the following procedure. A blank worksheet is at "Planning a VPN" on page 6-3. 6-6 Virtual Private Networking (Advanced Feature) v1.1, October 2006

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Reference Manual for the ADSL Modem Router DG834 v3
6-6
Virtual Private Networking (Advanced Feature)
v1.1, October 2006
How to Set Up a Client-to-Gateway VPN Configuration
Setting up a VPN between a remote PC running the NETGEAR ProSafe VPN Client and a
network gateway (see
Figure 6-3
) involves the following two steps:
•
“Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834 v3” on page 6-6
uses
the VPN Wizard to configure the VPN tunnel between the remote PC and network gateway.
•
“Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC” on page 6-11
configures the NETGEAR ProSafe VPN Client endpoint.
Step 1: Configuring the Client-to-Gateway VPN Tunnel on the
DG834 v3
The worksheet below identifies the parameters used in the following procedure. A blank
worksheet is at
“Planning a VPN” on page 6-3
.
Figure 6-3
Note:
This section uses the VPN Wizard to set up the VPN tunnel using the VPNC
default parameters listed in
Table 6-2 on page 6-4
. If you have special requirements
not covered by these VPNC-recommended parameters, refer to
“How to Set Up
VPN Tunnels in Special Circumstances” on page 6-36
to set up the VPN tunnel.
192.168.3.1
VPN Tunnel
DG834
22.23.24.25
PC
(Running NETGEAR
ProSafe VPN Client)
PCs
0.0.0.0