Nokia NBB0150000 Installation Guide - Page 55

Before You Start, A Phillips-head screwdriver

Get Nokia NBB0150000 - IP150 - Security Appliance PDF manuals and user guides View all Nokia NBB0150000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Installing or Replacing the Nokia Encryption Accelerator Card Caution To protect the appliance and the encryption accelerator card from electrostatic discharge damage, make sure you are properly grounded before you touch these components. Use a grounding wrist strap and follow the instructions provided with the wrist strap before you handle the components or open the appliance. If you do not have a grounding wrist strap, make sure you are properly grounded before you touch any electronic component. You must perform an orderly shutdown of the appliance and turn the power off whenever you remove the chassis tray assembly to service internal components. Before You Start To install or replace the encryption accelerator card in your appliance, you need the following: „ Physical access to the appliance „ A Nokia-approved encryption accelerator card „ Access to the appliance through Network Voyager „ A Phillips-head screwdriver To install or replace a Nokia encryption accelerator card 1. Use Network Voyager or the CLI to halt the appliance. To use Network Voyager to shut the appliance down, select System > Configuration > Reboot or Shutdown > Halt. To use the CLI to shut the appliance down, enter halt at the prompt. 2. Remove the power cord from the IP150 appliance, and remove the appliance from the rack. 3. Place the appliance right-side up and place it on a safe and protected work surface. Nokia IP150 Security Platform Installation Guide 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Installing or Replacing the Nokia Encryption Accelerator Card
Nokia IP150 Security Platform Installation Guide
55
Caution
To protect the appliance and the encryption accelerator card from electrostatic
discharge damage, make sure you are properly grounded before you touch these
components. Use a grounding wrist strap and follow the instructions provided with the
wrist strap before you handle the components or open the appliance. If you do not have
a grounding wrist strap, make sure you are properly grounded before you touch any
electronic component.
You must perform an orderly shutdown of the appliance and turn the power off whenever you
remove the chassis tray assembly to service internal components.
Before You Start
To install or replace the encryption accelerator card in your appliance, you need the following:
Physical access to the appliance
A Nokia-approved encryption accelerator card
Access to the appliance through Network Voyager
A Phillips-head screwdriver
To install or replace a Nokia encryption accelerator card
1.
Use Network Voyager or the CLI to halt the appliance.
To use Network Voyager to shut the appliance down, select
System > Configuration > Reboot or Shutdown > Halt.
To use the CLI to shut the appliance down, enter halt at the prompt.
2.
Remove the power cord from the IP150 appliance, and remove the appliance from the rack.
3.
Place the appliance right-side up and place it on a safe and protected work surface.