NordicTrack 9600 Plat Treadmill English Manual - Page 30

Roller Bolts 82 into the Roller Guards and thread them into the Rear Roller 79. Reattach the Motor

Get NordicTrack 9600 Plat Treadmill PDF manuals and user guides View all NordicTrack 9600 Plat Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

TURNING THE WALKING PLATFORM Both sides of the walking platform are designed to be used as walking surfaces. Inspect the walking platform periodically for wear. If there is any wood showing through the phenolic coating, or if the surface is damaged, the walking platform should be turned over. The walking platform will need to be turned over after every 10,000 to 15,000 miles. Follow the instructions below to turn over the walking platform. 1. Remove the key and unplug the power cord. Remove the two 1-3 Hood Screws (2) and lift off the 1 2 Motor Hood (1). Next, remove the two Rear Roller Bolts (82), the two Roller Guard Screws (80), 80 6 and the Right and Left Roller 83 6 Guards (81, 83). 82 2. Remove the six Platform Screws 70 80 (6). (Note: Be very careful when removing the Platform Screws and when handling the Walking 81 6 82 Platform [70]. The phenolic coating on the Walking 71 Platform can be chipped or 79 damaged if it is mishandled.) Lift the Rear Roller (79) and slide it out of the Walking Belt (71). Lift the Walking Platform (70) a few inches, slide it out of the Walking Belt, turn it over, and then slide it back into the Walking Belt. Slide the Rear Roller back into the Walking Belt. Reattach the six Platform Screws (6). 3. Reattach the Right and Left Roller Guards (81, 83) with the two Roller Guard Screws (80). Insert the Rear Roller Bolts (82) into the Roller Guards and thread them into the Rear Roller (79). Reattach the Motor Hood (1) with the two Hood Screws (2). 4. Next, the Walking Belt (71) will need to be adjusted to the proper tension. Using chalk, make two marks on the 4 71 Walking Belt exactly 50" apart, as shown in the drawing. Tighten both Rear Roller Bolts (82) until the two chalk marks move apart an additional 3/16" to 1/4". Make sure to keep the Walking Belt centered. 50" 82 REPLACING THE WALKING PLATFORM When both sides of the walking platform become worn, the walking platform should be replaced. The walking platform will need to be replaced after every 20,000 to 30,000 miles. Refer to page 44 to order a new walking platform. Follow the instructions above to replace the walking platform. REPLACING THE WALKING BELT When the walking belt becomes worn, it should be replaced. The walking belt will need to be replaced after every 20,000 to 30,000 miles. Refer to page 44 to order a new walking belt. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
TURNING THE WALKING PLATFORM
Both sides of the walking platform are designed to be used as walking surfaces. Inspect the walking platform peri-
odically for wear. If there is any wood showing through the phenolic coating, or if the surface is damaged, the
walking platform should be turned over. The walking platform will need to be turned over after every 10,000 to
15,000 miles. Follow the instructions below to turn over the walking platform.
1.
Remove the key and unplug the
power cord.
Remove the two
Hood Screws (2) and lift off the
Motor Hood (1). Next, remove the
two Rear Roller Bolts (82), the
two Roller Guard Screws (80),
and the Right and Left Roller
Guards (81, 83).
2.
Remove the six Platform Screws
(6).
(Note: Be very careful when
removing the Platform Screws
and when handling the Walking
Platform [70]. The phenolic
coating on the Walking
Platform can be chipped or
damaged if it is mishandled.)
Lift the Rear Roller (79) and slide
it out of the Walking Belt (71). Lift
the Walking Platform (70) a few inches, slide it out of the Walking Belt, turn it over, and then slide it back into
the Walking Belt. Slide the Rear Roller back into the Walking Belt. Reattach the six Platform Screws (6).
3.
Reattach the Right and Left Roller Guards (81, 83) with the two Roller Guard Screws (80). Insert the Rear
Roller Bolts (82) into the Roller Guards and thread them into the Rear Roller (79). Reattach the Motor Hood
(1) with the two Hood Screws (2).
4.
Next, the Walking Belt (71) will need to be adjusted to the
proper tension. Using chalk, make two marks on the
Walking Belt exactly 50” apart, as shown in the drawing.
Tighten both Rear Roller Bolts (82) until the two chalk
marks move apart an additional 3/16” to 1/4”. Make sure to
keep the Walking Belt centered.
REPLACING THE WALKING PLATFORM
When both sides of the walking platform become worn, the walking platform should be replaced. The walking
platform will need to be replaced after every 20,000 to 30,000 miles. Refer to page 44 to order a new walking plat-
form. Follow the instructions above to replace the walking platform.
REPLACING THE WALKING BELT
When the walking belt becomes worn, it should be replaced. The walking belt will need to be replaced after every
20,000 to 30,000 miles. Refer to page 44 to order a new walking belt.
30
6
6
6
80
80
82
82
70
79
71
1
2
81
83
50”
4
71
82
1–3