NordicTrack 9600 Plat Treadmill English Manual - Page 7

How To Set Up The Treadmill

Get NordicTrack 9600 Plat Treadmill PDF manuals and user guides View all NordicTrack 9600 Plat Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

HOW TO SET UP THE TREADMILL Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly can be completed using the included allen wrenches. 1. Slide the Right and Left Uprights (95, 97) onto the brackets near the front of the Frame (76). Make sure that the 1 Uprights are on the correct sides; the indicated holes must be facing the treadmill. Raise the Right Upright (95) until the lower hole in the 97 front of the Upright is aligned with the upper hole in the bracket. Thread an Upright Bolt (96) into the Upright and the bracket. Do not fully tighten the Upright Bolt yet. Holes 96 95 96 Repeat this step with the Left Upright (97). 76 2. While a second person holds the Handrail (91) near the Uprights (95, 97), feed the wires in both sides of the Handrail down into the Uprights. Pull the ends of the wires out of the lower ends of the Uprights. If there are wire ties on the ends of the wires, remove them. Finger tighten eight Handrail Bolts (99) into the Uprights (95, 97) and the Handrail (91). Do not tighten the Handrail Bolts yet. Be careful to avoid pinching the wires. Note: The CD Holder (86) and the Cup Holder (85) are replaceable. If these parts become dislodged from the Console Assembly, simply press them back into place. 2 Console Assembly 86 99 91 99 85 99 97 Wires 95 3. Connect the TV Cable (17) and the Right Power Wire 3 Harness (57) in the indicated locations. Make sure to 95 connect the Right Power Wire Harness properly. The 97 connectors should slide together easily and snap into place. If they do not, turn the Right Power Wire Harness and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Push all of the excess wire up into the Uprights (95, 97). Make sure that all wires are fully connected. Note: Regardless of which console your treadmill has, con- nect all wires so that the console can later be up- 17 57 graded if desired. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
7
Assembly requires two persons.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Assembly can be completed using the included
allen wrenches.
3.
Connect the TV Cable (17) and the Right Power Wire
Harness (57) in the indicated locations.
Make sure to
connect the Right Power Wire Harness properly. The
connectors should slide together easily and snap
into place.
If they do not, turn the Right Power Wire
Harness and try again.
IF THE CONNECTORS ARE
NOT CONNECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS TURNED ON.
Push all of the excess wire up into the Uprights (95, 97).
Make sure that all wires are fully connected. Note:
Regardless of which console your treadmill has, con-
nect all wires so that the console can later be up-
graded if desired.
2.
While a second person holds the Handrail (91) near the
Uprights (95, 97), feed the wires in both sides of the
Handrail down into the Uprights. Pull the ends of the
wires out of the lower ends of the Uprights. If there are
wire ties on the ends of the wires, remove them.
Finger tighten eight Handrail Bolts (99) into the Uprights
(95, 97) and the Handrail (91).
Do not tighten the
Handrail Bolts yet. Be careful to avoid pinching the
wires.
Note: The CD Holder (86) and the Cup Holder (85) are
replaceable. If these parts become dislodged from the
Console Assembly, simply press them back into place.
97
91
86
Console Assembly
85
99
99
99
Wires
2
1.
Slide the Right and Left Uprights (95, 97) onto the brack-
ets near the front of the Frame (76).
Make sure that the
Uprights are on the correct sides; the indicated holes
must be facing the treadmill.
Raise the Right Upright (95) until the lower hole in the
front of the Upright is aligned with the upper hole in the
bracket. Thread an Upright Bolt (96) into the Upright and
the bracket.
Do not fully tighten the Upright Bolt yet.
Repeat this step with the Left Upright (97).
95
96
96
76
97
H
OW TO
S
ET
U
P THE
T
READMILL
17
57
3
Holes
1
95
95
97