NordicTrack S3000 Treadmill English Manual - Page 22

Troubleshooting

Get NordicTrack S3000 Treadmill PDF manuals and user guides View all NordicTrack S3000 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

TROUBLESHOOTING Most treadmill problems can be solved by following the steps outlined in this section. Find any symptoms that apply, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. 1. SYMPTOM: THE POWER DOES NOT TURN ON a. Make sure that the power cord is fully plugged into the treadmill. In addition, make sure that the power cord is plugged into a properly grounded outlet (see page 9). b. Make sure that the key is inserted into the console. c. Check the reset/off circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in. 2. SYMPTOM: THE POWER TURNS OFF DURING USE Reset Position 50" a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in. c. Remove the key from the console. Reinsert the key into the console. d. Make sure that the reset/off circuit breaker is in the "reset" position. e. If the treadmill still will not run, please see the front cover of this manual. 3. SYMPTOM: THE WALKING BELT SLOWS WHEN WALKED ON a. If the walking belt is overtightened, performance may decrease and the walking belt may be damaged. If the walking belt is properly tightened, you should be able to lift each edge of the walking belt 1 to 2 in. (3 to 5 cm) off the walking platform. If adjustments need to be made, first remove the key and unplug the power cord. Using the included hex key, turn both roller bolts counterclockwise 1/4 of a turn. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and use the treadmill for a few minutes. Repeat until the walking belt is properly tightened. a Roller Bolts 1-2 in. b. If the walking belt still slows when walked on, please see the front cover of this manual. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
22
Most treadmill problems can be solved by following the steps outlined in this section. Find any symptoms
that apply, and follow the steps listed. If further assistance is needed, please see the front cover of this
manual.
1. SYMPTOM: THE POWER DOES NOT TURN ON
a. Make sure that the power cord is fully plugged into the treadmill. In addition, make sure that the power cord
is plugged into a properly grounded outlet (see page 9).
b. Make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the treadmill near the power
cord. If the switch protrudes as shown, the circuit breaker has tripped. To
reset the circuit breaker, wait for five minutes and then press the switch
back in.
2. SYMPTOM: THE POWER TURNS OFF DURING USE
a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see drawing above). If
the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes,
and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. Make sure that the reset/off circuit breaker is in the “reset” position.
e. If the treadmill still will not run, please see the front cover of this manual.
3. SYMPTOM: THE WALKING BELT SLOWS WHEN WALKED ON
a. If the walking belt is overtightened, performance may de-
crease and the walking belt may be damaged. If the walking
belt is properly tightened, you should be able to lift each
edge of the walking belt 1 to 2 in. (3 to 5 cm) off the walking
platform.
If adjustments need to be made, first remove
the key and unplug the power cord
. Using the included
hex key, turn both roller bolts counterclockwise 1/4 of a turn.
Be careful to keep the walking belt centered. Then, plug in
the power cord, insert the key, and use the treadmill for a
few minutes. Repeat until the walking belt is properly tight-
ened.
b. If the walking belt still slows when walked on, please see the front cover of this manual.
TROUBLESHOOTING
Reset
Position
a
Roller
Bolts
1–2 in.