NordicTrack S3000 Treadmill English Manual - Page 6

Assembly

Get NordicTrack S3000 Treadmill PDF manuals and user guides View all NordicTrack S3000 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly can be completed using the included hex keys. 1. Slide the Right and Left Uprights (95, 97) onto the brackets near the front of the Frame (76). Make sure that the 1 Uprights are on the correct sides; the indicated holes must be facing inward. Holes 96 Raise the Right Upright (95) until the lower hole in the 97 front of the Right Upright is aligned with the upper hole in the bracket on the Frame (76). Finger tighten an Upright Bolt (96) into the Right Upright and the bracket. Do not tighten the Upright Bolt yet. 95 96 Repeat this step with the Left Upright (97). 76 2. While a second person holds the Handrail (91) near the Uprights (95, 97), feed the Upright Wire Harness (100) in the right Handrail down into the right Upright. Pull the end of the Upright Wire Harness out of the lower end of the right Upright. If there is a wire tie on the end of the Upright Wire Harness, remove it. Then, set the Handrail on the Uprights. Finger tighten eight Handrail Bolts (99) into the Uprights (95, 97) and the Handrail (91). Do not tighten the Handrail Bolts yet. Be careful to avoid pinching the Wire Harness (57). Note: The CD Holder (86) and the Cup Holder (85) are replaceable. If these parts become dislodged from the Console Base (89), simply press them back in. 3. Connect the Upright Wire Harness (100) in the indicated location. Push all the excess wire up into the right Upright (95). Make sure that the Upright Wire Harness is fully connected. 2 86 99 91 99 97 100 3 89 85 99 95 95 100 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
6
Assembly requires two persons.
Set the treadmill in a cleared area and remove all packing materials.
Do not
dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly can be completed using the included hex keys.
2.
While a second person holds the Handrail (91) near the
Uprights (95, 97), feed the Upright Wire Harness (100) in
the right Handrail down into the right Upright. Pull the
end of the Upright Wire Harness out of the lower end of
the right Upright. If there is a wire tie on the end of the
Upright Wire Harness, remove it. Then, set the Handrail
on the Uprights.
Finger tighten eight Handrail Bolts (99) into the Uprights
(95, 97) and the Handrail (91).
Do not tighten the
Handrail Bolts yet. Be careful to avoid pinching the
Wire Harness (57).
Note: The CD Holder (86) and the Cup Holder (85) are
replaceable. If these parts become dislodged from the
Console Base (89), simply press them back in.
1.
Slide the Right and Left Uprights (95, 97) onto the brack-
ets near the front of the Frame (76).
Make sure that the
Uprights are on the correct sides; the indicated
holes must be facing inward.
Raise the Right Upright (95) until the lower hole in the
front of the Right Upright is aligned with the upper hole in
the bracket on the Frame (76). Finger tighten an Upright
Bolt (96) into the Right Upright and the bracket.
Do not
tighten the Upright Bolt yet.
Repeat this step with the Left Upright (97).
ASSEMBLY
95
96
76
97
Holes
1
97
91
86
89
85
99
99
99
100
2
95
96
3.
Connect the Upright Wire Harness (100) in the indicated
location. Push all the excess wire up into the right
Upright (95).
Make sure that the Upright Wire Harness
is fully connected.
3
95
100