Oki B710n B710, B720, B730 Setup Guide (English, Fran栩s, Espa?ol, P - Page 6

Preparing a location for the, printer, Install the Face Up Rear, Install the Drum-Toner, Cartridge - supplies

Get Oki B710n PDF manuals and user guides View all Oki B710n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Preparing a location for the printer Place the machine on a level and sturdy surface that can withstand the machine weight, 50 lb. (22.6 kg). If tilted, the machine may fall over and cause injuries. Space requirements The printer has ventilation holes on the side and rear panels. Ensure that the printer is installed with a minimum clearance of: • Rear: 10 inches (255 mm) • Left Side: 8 inches (200 mm) • Right Side: 12 inches (300 mm) • Front: 16 inches (402 mm) A poorly ventilated machine can cause excessive internal heat and fire. Environmental Requirements Ensure that the installation location meets the following conditions: • Do not place the printer in a hot, humid, dusty or poorly ventilated environment. Prolonged exposure to such adverse conditions can result in fire or electric shock. • Temperature range 50 - 89°F (10 - 32°C ). • Humidity range 15 - 85% (no condensation). • Humidity should be 70% or below at 89°F (32°C), and temperature should be 82°F (28°C) or below at 85% humidity. NOTE Sudden temperature fluctuations can affect print quality. Rapid heating of a cold room or moving the printer from a location with low humidity/temperature to high humidity/ temperature can cause condensation inside the printer, directly interfering with image transfer. When condensation occurs, leave the printer for at least 1 hour to acclimate to the environment before using it. • Do not expose the printer to direct sunlight. • Do not expose the printer to the direct draft of airconditioning or heating. Install the Face Up (Rear) Tray 1. Insert the right and left tabs of the face up (rear) tray into the holes at the back of the printer (1), and lower the tray into position (2). 2. Push up the rear output tray lever as shown in the diagram (1) and pull out the extension tray (2). Install the Drum-Toner Cartridge NOTE Your printer is supplied with a drum-toner cartridge with an approximate capacity of 10,000 Letter pages at 5% coverage. Replacement drum-toner cartridges are available with approximate capacities of 15,000 pages, 20,000 pages or 25,000 pages. 6 / English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
6 / English
Preparing a location for the
printer
Place the machine on a level and sturdy surface that
can withstand the machine weight, 50 lb. (22.6 kg). If
tilted, the machine may fall over and cause injuries.
Space requirements
The printer has ventilation holes on the side and rear
panels. Ensure that the printer is installed with a
minimum clearance of:
•
Rear: 10 inches (255 mm)
•
Left Side: 8 inches (200 mm)
•
Right Side: 12 inches (300 mm)
•
Front: 16 inches (402 mm)
A poorly ventilated machine can cause excessive
internal heat and fire.
Environmental Requirements
Ensure that the installation location meets the following
conditions:
•
Do not place the printer in a hot, humid, dusty or
poorly ventilated environment. Prolonged exposure
to such adverse conditions can result in fire or
electric shock.
•
Temperature range 50 – 89°F (10 – 32°C ).
•
Humidity range 15 – 85% (no condensation).
•
Humidity should be 70% or below at 89°F (32°C),
and temperature should be 82°F (28°C) or below at
85% humidity.
•
Do not expose the printer to direct sunlight.
•
Do not expose the printer to the direct draft of air-
conditioning or heating.
Install the Face Up (Rear)
Tray
1.
Insert the right and left tabs of the face up (rear)
tray into the holes at the back of the printer (1),
and lower the tray into position (2).
2.
Push up the rear output tray lever as shown in the
diagram (1) and pull out the extension tray (2).
Install the Drum-Toner
Cartridge
NOTE
Sudden temperature fluctuations can affect
print quality. Rapid heating of a cold room or
moving the printer from a location with low
humidity/temperature to high humidity/
temperature can cause condensation inside the
printer, directly interfering with image transfer.
When condensation occurs, leave the printer
for at least 1 hour to acclimate to the
environment before using it.
NOTE
Your printer is supplied with a drum-toner
cartridge with an approximate capacity of
10,000 Letter pages at 5% coverage.
Replacement drum-toner cartridges are
available with approximate capacities of
15,000 pages, 20,000 pages or 25,000 pages.