Oki C5400 OkiLAN 8100 SoftNIC User's Guide - Page 115

TCP/IP, Check the IP Address, Subnet Mask and Gateway are correct.

Get Oki C5400 PDF manuals and user guides View all Oki C5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 115 highlights

TCP/IP Printer cannot find the network interface card. Turn the printer off and on again. Confirm the network interface is enabled on the printer. Check there is a response to the interface card command. Check the network cable is correctly connected. Change the cable and try again. Run the Self-diagnostic test. Check the IP Address, Subnet Mask and Gateway are correct. Check that the TCP/IP protocol is set to Enable. Reset the network interface card to factory default settings. If DHCP, BOOTP and RARP are not used, ensure they have been set to Disable. Cannot print with lpr and ftp. Turn the printer off and on again. Check there is a response to the ping command. Check the network cable is correctly connected. Change the cable and try again. Check the host name and IP address are configured in the workstation. Check the printer port name is configured in the workstation. There are three port names: lp, euc and sjis. Use lp by default as euc and sjis are specific to printers with PostScript available. Incorrect User name on the banner page. If printing with lpr, the User name printed is unknown and the Filename printed is the Spool file name. Troubleshooting 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Troubleshooting 113
TCP/IP
Printer cannot find the network interface card
.
Turn the printer off and on again.
Confirm the network interface is enabled on the printer.
Check there is a response to the interface card command.
Check the network cable is correctly connected.
Change the cable and try again.
Run the Self-diagnostic test.
Check the IP Address, Subnet Mask and Gateway are correct.
Check that the TCP/IP protocol is set to Enable.
Reset the network interface card to factory default settings.
If DHCP, BOOTP and RARP are not used, ensure they have been set to
Disable.
Cannot print with lpr and ftp.
Turn the printer off and on again.
Check there is a response to the ping command.
Check the network cable is correctly connected.
Change the cable and try again.
Check the host name and IP address are configured in the workstation.
Check the printer port name is configured in the workstation.
There are three port names: lp, euc and sjis. Use lp by default as euc and
sjis are specific to printers with PostScript available.
Incorrect User name on the banner page.
If printing with lpr, the User name printed is unknown and the Filename
printed is the Spool file name.