Oki C5400 OkiLAN 8100 SoftNIC User's Guide - Page 118

NetBEUI, Check Ethernet is selected in AppleTalk. In some OS versions Network

Get Oki C5400 PDF manuals and user guides View all Oki C5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

If the network resides in a Zone, check the correct Zone name is selected in the Chooser. Check the Zone name in the utility related to the NIC is the same as the Zone name set in NIC. Check AppleTalk, which is displayed at the right bottom of the Chooser, is set to Enable. (In some OS versions Network is used instead of AppleTalk.) Check Ethernet is selected in AppleTalk. (In some OS versions Network is used instead of AppleTalk.) Check the print driver is selected in the Chooser. Check the EtherTalk protocol is set to Enable. Print the NIC settings and confirm that the EtherTalk Port name is not blank. NetBEUI The network interface card is not identified. Turn the printer off and on again. Check the network cable is correctly connected. Change the cable and try again. Check Microsoft network client and NetBEUI have been added to the network section of the control panel. Check the NetBEUI protocol is set to Enable. Check the factory setting of the workgroup name is PrintServer and the computer name is ML+ the last six digits of the MAC address. Check the computer name of the NIC is different from the computer name on the network. Troubleshooting 116

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Troubleshooting 116
If the network resides in a Zone, check the correct Zone name is selected
in the Chooser.
Check the Zone name in the utility related to the NIC is the same as the
Zone name set in NIC.
Check AppleTalk, which is displayed at the right bottom of the Chooser,
is set to Enable. (In some OS versions Network is used instead of
AppleTalk.)
Check Ethernet is selected in AppleTalk. (In some OS versions Network
is used instead of AppleTalk.)
Check the print driver is selected in the Chooser.
Check the EtherTalk protocol is set to Enable.
Print the NIC settings and confirm that the EtherTalk Port name is not
blank.
NetBEUI
The network interface card is not identified.
Turn the printer off and on again.
Check the network cable is correctly connected.
Change the cable and try again.
Check Microsoft network client and NetBEUI have been added to the
network section of the control panel.
Check the NetBEUI protocol is set to Enable.
Check the factory setting of the workgroup name is PrintServer and the
computer name is ML+ the last six digits of the MAC address.
Check the computer name of the NIC is different from the computer name
on the network.