Oki C9300n C9300/C9500 User's Guide: Macintosh - Page 202
Toner rubs off the printed surface.
View all Oki C9300n manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 202 highlights
Toner rubs off the printed surface. Possible cause Media Weight and Media Type settings may not be appropriate. Packing materials left on the fuser when it was installed. Remedy Set the value of media weight to the next heaviest one. Careful! Fuser may be HOT! Open the top cover and check to be sure that all packing materials were removed from the fuser. To remove the fuser, see "Changing the fuser unit" on page 174. C9300/C9500 Troubleshooting • 200
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
C9300/C9500 Troubleshooting • 200
Toner rubs off the printed surface.
Possible cause
Remedy
Media Weight and Media Type
settings may not be appropriate.
Set the value of media weight to the
next heaviest one.
Packing materials left on the fuser
when it was installed.
Careful
! Fuser may be
HOT
! Open the
top cover and check to be sure that all
packing materials were removed from
the fuser. To remove the fuser, see
“Changing the fuser unit” on page 174.