Panasonic AG-MSU10 Operating Instructions - Page 47

Message, Description, Measure, TURN POWER - p2 media storage unit

Get Panasonic AG-MSU10 PDF manuals and user guides View all Panasonic AG-MSU10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Message STORAGE DEVICE DISCONNECTED! SYSTEM ERROR! TOO MANY CLIPS! TOO MANY FOLDERS! TOO MANY PARTITIONS! TOO MANY TARGETS! TURN POWER OFF! UNKNOWN CONTENTS FORMAT! UNKNOWN DEVICE CONNECTED! VERIFICATION FAILED! WRITE PROTECTED! Description Measure The unit has been disconnected from the storage device. Connect the storage device properly. If the device still does not operate normally, turn it off and turn it back on again. Last copy or format operation failed due to Copy or format again. a system control error. Too many clips are selected. Reduce the number of selected clips. There are too many folders on the storage device. There are too many partitions on the storage device. There are too many devices connected to hubs. Displayed when an error occurs in reading and writing P2 card or storage device data. An attempt was made to process an unknown clip (clip version not supported by this unit) or a bad clip. An unsupported DVD drive or unsupported device is connected. The maximum number of folders is 100. Use a new storage device or a formatted storage device. Storage devices can handle up to 23 partitions. Use a new or formatted storage device. Disconnect the device, turn off the unit and turn it back on again. To continue operation, turn the power off and then back on again. Use only clips that are supported by the unit. Restore bad clips on the device that recorded them or delete them. Disconnect the device, turn off the unit and turn it back on again. The contents of the copied data do not match. The P2 card is write protected. Copy the data again. Insert write-enabled media. For long and Trouble-free Operation 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
³¶
For long and Trouble-free Operation
Message
Description
Measure
STORAGE
DEVICE
DISCONNECTED!
The unit has been disconnected from the
storage device.
Connect the storage device properly. If
the device still does not operate normally,
turn it off and turn it back on again.
SYSTEM
ERROR!
Last copy or format operation failed due to
a system control error.
Copy or format again.
TOO MANY
CLIPS!
Too many clips are selected.
Reduce the number of selected clips.
TOO MANY
FOLDERS!
There are too many folders on the storage
device.
The maximum number of folders is 100.
Use a new storage device or a formatted
storage device.
TOO MANY
PARTITIONS!
There are too many partitions on the stor-
age device.
Storage devices can handle up to 23
partitions. Use a new or formatted storage
device.
TOO MANY
TARGETS!
There are too many devices connected to
hubs.
Disconnect the device, turn off the unit
and turn it back on again.
TURN POWER
OFF!
Displayed when an error occurs in read-
ing and writing P2 card or storage device
data.
To continue operation, turn the power off
and then back on again.
UNKNOWN
CONTENTS
FORMAT!
An attempt was made to process an un-
known clip (clip version not supported by
this unit) or a bad clip.
Use only clips that are supported by the
unit.
Restore bad clips on the device that
recorded them or delete them.
UNKNOWN
DEVICE
CONNECTED!
An unsupported DVD drive or unsupport-
ed device is connected.
Disconnect the device, turn off the unit
and turn it back on again.
VERIFICATION
FAILED!
The contents of the copied data do not
match.
Copy the data again.
WRITE
PROTECTED!
The P2 card is write protected.
Insert write-enabled media.