Panasonic KXTG5243 5.8ghz Cdl Multi H/s - Page 84

TROUBLESHOOTING, Wrong handset, Refer to manual

Get Panasonic KXTG5243 - KXTG5240M TOT 3 H/S PDF manuals and user guides View all Panasonic KXTG5243 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

If the Following Appear on Your Display... Display message Wrong handset Refer to manual Cause & Remedy • This handset is not for this base unit. This handset is for KX-TG6500 base unit. The accessory handsets for this base unit are KX-TGA520 and KX-TGA523. To order, see page 3. Troubleshooting If the handset display shows error messages, see "If the Following Appear on Your Display..." (p. 82-84) for the Cause & Remedy. Telephone System Problem "No link to base. Move closer to base and try again." is displayed and an alarm tone sounds. Static, sound cuts in/out, fades. Interference from other electrical units. The base unit and/or handset does not ring. The handset display is blank. You cannot program any function items. Cause & Remedy • The handset has lost communication with the base unit. Walk closer to the base unit, and try again. • Confirm the base unit's AC adaptor is plugged in. • Raise the base unit antennas. • The handset's registration may have been canceled. Re-register the handset (p. 80, 81). • Move the handset and base unit away from other electrical appliances (p. 6). • Walk closer to the base unit. • Raise the base unit antennas. • Turn on the Clarity Booster feature (p. 29). • If the unit is connected to a telephone line with DSL service, you may hear noise from the receiver or speaker during conversations. We recommend connecting a noise filter (contact your DSL service provider) to the telephone line between the unit and the telephone line jack. • The ringer volume is turned off. Set to high, medium, or low (p. 20, 21). • If more than one other user is using the handset and/or base unit, the handset/base unit may not ring. Users will hear incoming call tones (p. 59). • If the handset display is blank, fully charge the battery (p. 13). • Programming is not possible while the handset and/or base unit is being used. • Do not pause for over 60 seconds while programming. • Walk closer to the base unit. • While another user is listening to messages or the Answering System is handling a call, you cannot program. Try again later. 84

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
84
If the Following Appear on Your Display...
Troubleshooting
If the handset display shows error messages, see “If the Following Appear on
Your Display...” (p. 82–84) for the Cause & Remedy.
Telephone System
Display message
Cause & Remedy
Wrong handset
Refer to manual
•
This handset is not for this base unit. This handset is
for KX-TG6500 base unit. The accessory handsets
for this base unit are KX-TGA520 and KX-TGA523.
To order, see page 3.
Problem
Cause & Remedy
“
No link to base.
Move closer to
base and try
again.
” is displayed and an
alarm tone sounds.
•
The handset has lost communication with the base
unit. Walk closer to the base unit, and try again.
•
Confirm the base unit’s AC adaptor is plugged in.
•
Raise the base unit antennas.
•
The handset’s registration may have been
canceled. Re-register the handset (p. 80, 81).
Static, sound cuts in/out,
fades. Interference from other
electrical units.
•
Move the handset and base unit away from
other electrical appliances (p. 6).
•
Walk closer to the base unit.
•
Raise the base unit antennas.
•
Turn on the Clarity Booster feature (p. 29).
•
If the unit is connected to a telephone line with
DSL service, you may hear noise from the
receiver or speaker during conversations. We
recommend connecting a noise filter (contact
your DSL service provider) to the telephone line
between the unit and the telephone line jack.
The base unit and/or handset
does not ring.
•
The ringer volume is turned off. Set to high,
medium, or low (p. 20, 21).
•
If more than one other user is using the handset
and/or base unit, the handset/base unit may not
ring. Users will hear incoming call tones (p. 59).
The handset display is blank.
•
If the handset display is blank, fully charge
the battery (p. 13).
You cannot program any
function items.
•
Programming is not possible while the
handset and/or base unit is being used.
•
Do not pause for over 60 seconds while programming.
•
Walk closer to the base unit.
•
While another user is listening to messages
or the Answering System is handling a call,
you cannot program. Try again later.