Pioneer DJM-2000NXS Operating Instructions - Page 27

REV ROLL1 2 Original Effect turned on 1/1 reverse roll Reversed and repeated This function records the input sound at the point at which the [ON/OFF] button is pressed, reverses the recorded sound and repeats it according to the beat button's fraction. Beat buttons (parameter 1) The effect time is set from 1/8 to 4/1 with respect to 1 beat of BPM time. TIME control (parameter 2) Use this to set the effect time. 10 to 4000 (ms) LEVEL/DEPTH control (parameter 3) Use this to set the balance between the original sound and ROLL. EFFECT FREQUENCY (parameter 4) Use these to set the balance between the original sound and the ROLL for the different bands. FILTER 1 Frequency This function changes the filter's cut-off frequency according to the beat button's fraction. Beat buttons (parameter 1) These set the cycle for moving the cut-off frequency from 1/8 to 4/1 with respect to 1 beat of BPM time. Use this to set the cycle at which the cut-off freTIME control (parameter 2) quency is moved. 10 to 32000 (ms) LEVEL/DEPTH control (parameter 3) The further the control is turned clockwise, the more the effect is stressed. The original sound is set when turned fully counterclockwise. EFFECT FREQUENCY (parameter 4) These set the balance between the original sound and the effect sound for the different bands. TRANS1 MIN MAX MIN MAX 1/1 beat Cut Time Cut Cut Cut MIN MAX EFFECT FREQUENCY This function cuts the sound according to the beat button's fraction. The amount of the sound to be cut can be changed at [EFFECT FREQUENCY]. Beat buttons (parameter 1) These set the 1/8 to 4/1 cut time with respect to 1 beat of BPM time. TIME control (parameter 2) Use this to set the effect time. 10 to 16000 (ms) LEVEL/DEPTH control (parameter 3) Sets the balance between the original sound and the effect sound. EFFECT FREQUENCY (parameter 4) This sets the amount of the original sound to be cut for the different bands. PHASER 1 Phase shift Cycle Time The phaser effect changes according to the beat button fraction. Beat buttons (parameter 1) These set the cycle for moving the phaser effect by 1/8 to 4/1 with respect to the time of one BPM beat. This sets the cycle by which the phaser effect is TIME control (parameter 2) moved. 10 to 32000 (ms) LEVEL/DEPTH control (parameter 3) The further the control is turned clockwise, the more the effect is stressed. When turned all the way counterclockwise, only the original sound is output. EFFECT FREQUENCY (parameter 4) Use these to set the balance between the original sound and the effect sound for the different bands. GATE 1 Level MIN MAX MIN MAX Threshold Threshold Time Threshold MIN MAX EFFECT FREQUENCY This function outputs the input sound that has a level above the threshold level, cutting the input sound that has a level below the threshold level. The threshold level can be changed at [EFFECT FREQUENCY]. Beat buttons (parameter 1) This sets the release time between 1 and 100 %. TIME control (parameter 2) This sets the release time. 1 to 100 (%) LEVEL/DEPTH control (parameter 3) Sets the threshold level. The further the control is turned clockwise, the more the effect is stressed and the sound is cut. EFFECT FREQUENCY (parameter 4) Use these to set the threshold levels for the different bands. SEND/RETURN1 SEND RETURN Effector DJM-2000NXS Connect an external effector, etc., here. [EFFECT FREQUENCY] can be used as an isolator. Beat buttons (parameter 1) - TIME control (parameter 2) - LEVEL/DEPTH control (parameter 3) This adjusts the sound level input to the [RETURN] terminal. EFFECT FREQUENCY (parameter 4) This sets the audio output level of the RETURN sound for the different bands. 1 When "A", "B" or "M" is selected with the [CH SELECT] buttons, the effect sound cannot be monitored by pressing [CUE] (BEAT EFFECT) unless the sound for the channel you want to monitor is being output from [MASTER] channel. 2 When BEAT EFFECT is off, the effect sound cannot be monitored by pressing [CUE] (BEAT EFFECT). En 27 English