Pioneer DJM-2000NXS Operating Instructions - Page 28

Changing the settings 1 1 Setup item button 1 Press [LIVE SAMPLER (UTILITY, WAKE UP)] for at least 1 seconds. The [USER SETUP] mode setting screen is displayed. The [LIVE SAMPLER (UTILITY, WAKE UP)] indicator flashes. ! To display the [CLUB SETUP] screen, first turn this unit's power off, then press [POWER] while pressing [LIVE SAMPLER (UTILITY, WAKE UP)]. 2 Press the setup item button. The selection items appear. 3 Select the setup item. Select the item on the touch panel and enter it. 4 Change the item's setting. Select the item on the touch panel and enter it. ! Press [SAVE] to save the changes to the [CLUB SETUP] screen. 5 Press [EXIT]. Close the [USER SETUP] mode setting screen. ! To close the [CLUB SETUP] mode setting screen, press the [POWER] button to turn this unit's power off. Setting preferences Settings indicated in italics are the default settings set upon purchase. Mode Options settings Selection item 1 Selection item 2 ZONE11 BUTTON ACTION MIDI CHANNEL MIDI BUTTON ACTION ZONE22 MIDI CHANNEL USER SETUP FADER START LINK CONTROL RESET CH1 to CH4 CH2, CH3 LCD VERSION No. BACK LIGHT - 1, 2, 3, 4, 5 - QUANTIZE QUANTIZE ON, OFF SYSTEM DIGITAL OUT MAX LEVEL -19 dB, -15 dB, -10 dB, -5 dB DIGITAL SAMPLING RATE 48 kHz, 96 kHz AUTO STANDBY ON, OFF OUTPUT TO BOOTH MONITOR ON, OFF CLUB SETUP MIC TALK OVER THRESHOLD -25 dB, -20 dB, LEVEL -15 dB, -10 dB TALK OVER LEVEL -25 dB, -20 dB, -15 dB, -10 dB TOUCH PANEL - - PEAK LIMITER FACTORY RESET PEAK LIMITER YES, NO ON, OFF - Selection item 3 Descriptions TOGGLE TRIGGER 1, 2, to 16 TOGGLE TRIGGER 1, 2, to 16 - ON, OFF ON, OFF - - - - - - - - - - - - Select the MIDI signal sending method, [TOGGLE] or [TRIGGER]. Sets the MIDI channel. Select the MIDI signal sending method, [TOGGLE] or [TRIGGER]. Sets the MIDI channel. Restores the [TYPE A] - [TYPE D] MIDI settings to the default values. [RESET] function is unique to [ZONE2]. Turns the fader start function on and off for all DJ players connected to the [LINK] terminals. Turns the fader start function of the DJ players connected to the [CONTROL] terminals on and off. Adjusts the touch panel's brightness. Displays this unit's software version. Turns use of the beat information obtained from the player on and off. Sets the maximum level of the sound output from the [DIGITAL OUT] terminals. 1 Sets the digital signal's sampling rate. Turns the auto standby function on and off. Sets whether or not to output the microphone's audio signals from [BOOTH] terminals. Sets the talkover sensitivity. The talkover function is activated when a sound with a volume above the set volume is input to the microphone. Sets the attenuation level for the sound other than the microphone's sound when the talkover function is activated. The touch panel's calibration is adjusted by pressing [+] in order. Alleviates sudden, unpleasant digital clipping of the master output. Restores all the settings to their factory defaults. 1 Changes the MIDI settings of the buttons on the control panel, [FREQUENCY MIX] and [SIDECHAIN REMIX]. 2 Changes the MIDI settings for [TYPE A] to [TYPE D] on the MIDI control screen. About the auto standby function When [AUTO STANDBY] is set to [ON], the standby mode is set automatically if 4 hours pass with all of the conditions below met. - That none of this unit's buttons or controls are operated. - That no audio signals of -10 dB or greater are input to this unit's input terminals. - That no PRO DJ LINK connections are made. ! The standby mode is canceled when [LIVE SAMPLER (UTILITY, WAKE UP)] is pressed. 28 En