Pioneer VSX-1015TX Owner's Manual - Page 75
Additional information, Specifications, Cleaning the unit - watts
View all Pioneer VSX-1015TX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 75 highlights
Additional information 12 Specifications Amplifier section Continuous average power output of 120 watts* per channel, min., at 8 ohms, from 20 Hz to 20,000 Hz with no more than 0.2%** total harmonic distortion (front). Continuous Power Output Front 120 W + 120 W (20 Hz-20 kHz, 8 Ω, 0.2%) Center 120 W (20 Hz-20 kHz, 8 Ω, 0.2%) Surround 120 W + 120 W (20 Hz-20 kHz, 8 Ω, 0.2%) Surround back 120 W + 120 W (20 Hz-20 kHz, 8 Ω, 0.2%) Continuous Power Output Front 150 W + 150 W (1 kHz, 6 Ω, 1.0%) Center 150 W (1 kHz, 6 Ω, 1.0%) Surround 150 W + 150 W (1 kHz, 6 Ω, 1.0%) Surround back 150 W + 150 W (1 kHz, 6 Ω, 1.0%) Total harmonic distortion 0.09% (20 Hz-20 kHz, 110 W, 8 Ω) Audio Section Input (Sensitivity/Impedance) LINE 335 mV/47 kΩ Frequency Response LINE 5 Hz to 100,000 Hz dB Output (Level/Impedance) REC 335 mV/2.2 kΩ Tone Control BASS 6 dB (100 Hz) TREBLE 6 dB (10 kHz) LOUDNESS 4/+2 dB (100Hz/10 kHz) (at volume position -40 dB) Signal-to-Noise Ratio (IHF, short circuited, A network) LINE 103 dB Signal-to-Noise Ratio [EIA, at 1W (1kHz)] LINE 83 dB * Measured pursuant to the Federal Trade Commission's Trade Regulation rule on Power Output Claims for Amplifiers ** Measured by Audio Spectrum Analyzer Composite Video / S-Video Section Input (Sensitivity/Impedance 1 Vp-p/75 Ω Output (Level/Impedance 1 Vp-p/75 Ω Signal-to-Noise Ratio 65 dB Frequency Response 5 Hz to 10 MHz dB Component Video Section Input (Sensitivity/Impedance 1 Vp-p/75 Ω Output (Level/Impedance 1 Vp-p/75 Ω Signal-to-Noise Ratio 65 dB Frequency Response 5 Hz to 100 MHz dB FM Tuner Section Frequency Range 87.5 MHz to 108 MHz Usable Sensitivity . . . . . .Mono: 13.2 dBf, IHF (1.3 µV/75 Ω) 50 dB Quieting Sensitivity Mono: 20.2 dBf Stereo: 38.6 dBf Signal-to-Noise Ratio Mono: 73 dB (at 85 dBf) Stereo: 70 dB (at 85 dBf) Distortion Stereo: 0.5% (1 kHz) Alternate Channel Selectivity 60 dB (400 kHz) Stereo Separation 40 dB (1 kHz) Frequency Response 30 Hz to 15 kHz ± 1dB Antenna Input 75 Ω unbalanced AM Tuner Section Frequency Range 530 kHz to 1,700 kHz Sensitivity (IHF, Loop antenna 350 µV/m Selectivity 25 dB Signal-to-Noise Ratio 50 dB Antenna Loop antenna Miscellaneous Power Requirements AC 120 V, 60 Hz Power Consumption 480 W, 630 VA In standby 0.43 W AC Outlet switched) 100 W MAX. Dimensions 420 (W) x 173 (H) x 465 (D) mm (16 9/16 (W) x 6 13/16 (H) x 18 5/16 (D) in.) Weight (without package 15.4 kg (34 lb) Furnished Parts Microphone (for Auto MCACC setup 1 AA/IEC R6P dry cell batteries 2 Remote control 1 AM loop antenna 1 FM wire antenna 1 Warranty card 1 These operating instructions Note • Specifications and the design are subject to possible modifications without notice, due to improvements. Cleaning the unit • Use a polishing cloth or dry cloth to wipe off dust and dirt. • When the surface is dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleansers. • Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit, since these will corrode the surface. 75 En