ProForm 650 English Manual - Page 13

Wrap the High Cable 73 around a 4 Pulley 35.

Get ProForm 650 PDF manuals and user guides View all ProForm 650 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

23. Remove the upper 3/8" x 3" Bolt (45) from the Top Frame (1) and the Main Upright (3). Route the High Cable (73) around a 4" Pulley (35) and down through the indicated slot in the Main Upright (3), as shown. Attach the Pulley inside the slot with a 3/8" x 2 1/2" Bolt (54), two 3/8" Washers (55), two 5/8" x 1/2" Bushings (42), and a 3/8" Nylon Jamnut (63). Re-insert the 3/8" x 3" Bolt (45) and secure it with a 3/8" Nylon Locknut (50). Note: The High Cable (73) must be seated in the groove of the 4" Pulley (35) before the Bolt is inserted. 23 1 35 Slot 45 55 54 50 42 73 63 55 42 3 24. Route the High Cable (73) under the welded tube 24 on the Press Frame (12) and around a 4" Pulley Welded Tube 59 (35) as shown. Attach the Pulley to the Press Frame with a 3/8" x 8 1/2" Bolt (59) and a 3/8" Nylon Locknut (50). 50 35 73 12 25. Wrap the High Cable (73) around a 4" Pulley (35). Attach the Pulley inside the indicated slot in the Main Upright (3) with a 3/8" x 2 1/2" Bolt (54), two 3/8" Washers (55), two 5/8" x 1/2" Bushings (42), and a 3/8" Nylon Jamnut (63). Wrap the High Cable (73) around another 4" Pulley (35) in the direction shown. Route the High Cable through the slot in the Main Upright (3). Attach the Pulley to the Press Frame (12) with a 3/8" x 8 1/2" Bolt (59) and a 3/8" Nylon Locknut (50). 25 35 42 63 55 Slot 50 54 42 55 59 73 12 35 3 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
13
23. Remove the upper 3/8” x 3” Bolt (45) from the
Top Frame (1) and the Main Upright (3).
Route the High Cable (73) around a 4” Pulley
(35) and down through the indicated slot in the
Main Upright (3), as shown. Attach the Pulley
inside the slot with a 3/8” x 2 1/2” Bolt (54), two
3/8” Washers (55), two 5/8” x 1/2” Bushings (42),
and a 3/8” Nylon Jamnut (63).
Re-insert the 3/8” x 3” Bolt (45) and secure it with
a 3/8” Nylon Locknut (50).
Note: The High Cable
(73) must be seated in the groove of the 4”
Pulley (35) before the Bolt is inserted.
23
Slot
35
73
55
54
42
55
3
42
63
45
50
1
25. Wrap the High Cable (73) around a 4” Pulley (35).
Attach the Pulley inside the indicated slot in the
Main Upright (3) with a 3/8” x 2 1/2” Bolt (54), two
3/8” Washers (55), two 5/8” x 1/2” Bushings (42),
and a 3/8” Nylon Jamnut (63).
Wrap the High Cable (73) around another 4” Pulley
(35) in the direction shown. Route the High Cable
through the slot in the Main Upright (3). Attach the
Pulley to the Press Frame (12) with a 3/8” x 8 1/2”
Bolt (59) and a 3/8” Nylon Locknut (50).
24
25
73
Welded Tube
50
50
35
59
73
42
42
63
55
55
54
59
3
12
35
12
Slot
35
24. Route the High Cable (73) under the welded tube
on the Press Frame (12) and around a 4” Pulley
(35) as shown. Attach the Pulley to the Press
Frame with a 3/8” x 8 1/2” Bolt (59) and a 3/8”
Nylon Locknut (50).