Sanyo VCC-HD5400 VCC-HD5400 Setup and Summary Manual
Sanyo VCC-HD5400 - Full HD 1080p Day/Night Pan-Tilt-Zoom Camera Manual
 |
UPC - 086483075698
View all Sanyo VCC-HD5400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo VCC-HD5400 manual content summary:
- Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 1
SUMMARY/SETUP MANUAL Megapixel Camera VCC-HD5400 VCC-HD5400P English Français Español THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES. Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 2
...13 Specifications...14 Copyright Notice ...16 ■ Accessories ᶃ Pattern sheet ᶄ Mounting plate ᶅ Hexagonal wrench ᶆ Fixer ᶇ CD-ROM ᶈ Clamping core: To prevent electromagnetic interference • VCC-HD5400 • VCC-HD5400P ×2 ×5 ■ Check your operating environment. To operate the camera via network - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 3
~ 12 VDC + ᶅ ᶄ ᶈ ᶃ 24 VAC /12 VDC Power cable ᶄ Alarm cables • Alarm input cable: Connect an external switch, ⦈ Address switch: Use this switch to configure the camera control address. ᶆ Network Socket (LAN: RJ-45, PoE) ᶇ EX-HDD super-fine HD (High Definition) video signal. Use the terminal - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 4
By connecting a system controller (sold separately), the camera can be controlled remotely. ᶊ Wire gutter cover jack to connect to the audio input jacks of a powered speaker system or a monitor. ⦈ Audio input terminal ( the video and sound. This jack supports 3.5-mm monaural microphone plugs, or - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 5
power indicator blinks when this button is pressed, and stays lit when the SD memory card is recognized. Installing Recording Media • Before you insert an SD card, be sure to turn off the camera. • If you insert an SD card, format it via network operation on the SD/HDD screen. ( Electronic manual - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 6
VCC-HD5400 - NC AC24 ~ ~ GND Power cable ⦍ GRAY YELLOW WHITE RS485(A) the instruction manual that HD video output terminal (HDMI). You cannot output the video simultaneously from HD video output terminal (HDMI) and from monitor output terminal (MONITOR OUT). When both terminals are used, the HD - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 7
USB ⦉ LAN VCC-HD5400P High-definition monitor BLACK WHITE DC12 + - NC AC24 ~ ~ GND Power cable External peripheral device Microphone Speaker System controller ~ ~ the case to the camera. *3: Connect the mini-USB (type B) connector of the USB cable to the camera, connect the other connector - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 8
to your router's Instruction manual. Port number (default): 80 (TCP) IP address (default): cameras, via network operation on the NETWORK SETTINGS screen, assign them with port numbers that are different from that of the first camera. ( Electronic manual) ■ Using PoE This camera supports PoE (Power - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 9
Electronic manual) • After connecting an alarm device, configure the input conditions for the corresponding alarm input cable via network operation on Power Connection Connect the power terminals (24 VAC/12 VDC) of the camera to a power supply. ᶃ Connection to 24 VAC power supply Although the power - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 10
cables to make the installation easier. (B) (C) (A) After binding, cut off the excess portion of the fixer. When routing cables through the side face of the camera Remove the wire gutter cover (AA). (AA) (C) If you use a USB cable or an HDMI cable, secure it along with the LAN cable using - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 11
cover and tighten the fall-prevention screw (E) using the supplied hexagonal wrench (F). • When finished, make sure to put the cover back. (F) (E) • The surface of the camera can be hot during operation, but it is not a malfunction. When you touch the heated portion of the - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 12
is set to "PELCO", set to 2400. Protocol Select the protocol for controlling the camera. Protocol SSP (SANYO) PELCO Switch 4 OFF ON Corresponding Protocol Automatic switching between Sanyo SSP and high speed SSP Automatic switching between PELCO-D and PELCO-P Terminator When you connect - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 13
79 79 207 ˓ ˓ ˓ ˓ ˓ 80 80 208 ˓˓ 81 81 209 ˓ ˓˓ 82 82 210 ˓ ˓˓ 83 83 211 ˓ ˓ ˓˓ 84 84 212 ˓˓˓ 85 85 213 ˓ ˓ ˓ ˓ Address (Camera No.) Protocol Switch No. SANYO PELCO 1 2 3 4 5 6 7 86 86 214 ˓ ˓ ˓ ˓ 87 87 215 88 88 216 ˓˓ ˓ 89 89 217 ˓ ˓˓ ˓ 90 90 218 ˓ ˓ ˓ ˓ 91 91 219 92 92 - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 14
(instead of "http://"). Attempts to access the camera using the default IP address will fail if that address is already being used by another device in the network. If so, change the IP address of the existing device before accessing the camera. ⵈ Type your user name and password and click [OK]. The - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 15
, Japanese For further details on the specifications of the camera, refer to the electronic manual. ■ I/O Video output LAN EX- - 255 (sanyo SSP: 1 to 127) ■ Recording media SD memory card External HDD Normal recording, alarm recording, backup video recording in event of a network failure, log - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 16
Specifications ■ Network Image/video compression H.264/JPEG IP filtering ■ Others Operating ambient temperature/humidity Power source Power consumption Weight Dimensions -10 to +50°C/14 to 122°F, 90% RH or less (no condensation) VCC-HD5400: • 12 to 15 VDC • 24 VAC±10%, 60 Hz • PoE VCC-HD5400P - Sanyo VCC-HD5400 | VCC-HD5400 Setup and Summary Manual - Page 17
The instruction manual and the software are copyrighted by SANYO Electric Co., Ltd. No materials contained in the manual and the software may or the power is turned off while the card is being accessed. • The medium has reached the end of its service life. ■ License for Software Contained in
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
 |
 |
SUMMARY/SETUP MANUAL
VCC-HD5400
VCC-HD5400P
THIS INSTALLATION SHOULD BE MADE
BY A QUALIFIED SERVICE PERSON AND
SHOULD CONFORM TO ALL LOCAL
CODES.
Megapixel Camera
English
Français
Español
Deutsch
日本語
Before installing and using the camera, please read
this manual carefully.
Be sure to keep it handy for later reference.
In addition, be sure to read carefully the electronic
manual (INSTRUCTION MANUAL) contained in the
supplied CD-ROM to ensure correct operation of
the camera.
Important
Be careful when opening holes for installing
the unit. Work with the power and video cables
pulled out for easy installation.
Make sure to properly perform waterproofing for
the ceiling where you are installing the unit.
Make sure that the surface in the installation
location has no unevenness and is strong
enough to bear the total weight of the unit.
Install this unit in an environment where the
temperature range stays between –10°C and
+50°C/14°F and 122°F (no condensation
allowed).
As a precaution against static electricity
damage, touch a nearby metal object (door
knob, etc.) to dissipate static electricity in your
body before touching this unit.
•
•
•
•
•