Schwinn 130 Upright Bike 2020 model Service Manual

Schwinn 130 Upright Bike 2020 model Manual

Get Schwinn 130 Upright Bike 2020 model PDF manuals and user guides View all Schwinn 130 Upright Bike 2020 model manuals
Add to My Manuals
Save this manual to your list of manuals

Schwinn 130 Upright Bike 2020 model manual content summary:

  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 1
    TM Schwinn™ 130 / 510U (Model Year 2020) Upright Bike Service Manual Table of Contents Section Code Section 1 1 1 1 1 1 1 1 1 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Important Safety Instructions Safety Warning Labels and Serial Number FCC Compliance Specifications Maintenance
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 2
    Service Procedures Information for the Schwinn™ 130/ 510U (Model Year 2020) Bikes 8027931.021522.A NOTICE: This document provides important safety instructions, adjustments, and general troubleshooting information for the maintenance of the Schwinn™ 130 / 510U (Model Year 2020) Upright Bikes
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 3
    Manual for additional warnings and safety information. • The heart rate displayed is an approximation and should be used for reference only. • Not intended for use by anyone under 14 years uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 4
    location must be on a hard, level surface. Allow a workout area of a minimum 1.1 m x 1.65 m (44.9 in x 65 in). Keep at least 0.6 m (24 in) along the side used to access the machine and to the rear of the machine clear. 1.1 m (44.9 in) 0.6 m (24 in) 1.65 m (65 in) 0.6 m (24 in) 4
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 5
    Maintenance Read all maintenance instructions fully before you start any repair work. In some Disconnect all power to the machine before you service it. Daily: Before each use, examine the exercise machine for loose, broken, damaged, or worn parts. Do not use if found in this condition. Repair or
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 6
    Moving the Bike To move the upright bike, carefully tilt the Handlebars toward you while pushing the front of the bike downward. Push the bike to the desired location. NOTICE: B e careful when you move the bike. Abrupt motions can affect the computer operation. Leveling the Bike Levelers are found
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 7
    named Schwinn Toolbox™. The App is available on the App Store and Google Play™. Note: For a complete list of supported devices Monitor Connected icon. Follow the instructions provided with your Bluetooth® HR if provided) from the Heart Rate Sensor before use. 1. Put on your Bluetooth® Heart Rate
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 8
    replace the Console. If the above steps do not resolve the problem, contact Customer Service (if inside US/Canada) or your local distributor (if outside issues, Static Handlebar should be replaced. Follow the troubleshooting instructions provided with the device. HR monitor batteries Interference
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 9
    Problem Resistance does not change (machine turns on and operates) Console shuts off (enters sleep mode) while in use above steps do not resolve the problem, contact Customer Service (if inside US/Canada) bike is level. Adjustment may not be able to compensate for extremely uneven surfaces. Move bike
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 10
    Maintenance Parts Exploded View A J L C G J A K DD EE M R B H I N O P Q U V S T D E F BB CC Y AA J D Z X W C A Console B Console Mast C Pedals D Crank Arms E Left Shroud F Power Inlet G Right Shroud H Top Shroud I Mast Gasket J Data Cable K Handlebars L HR Cables M CHR Sensors N Seat O Seat
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 11
    Disconnect all power to the machine before you service it. When disposing of old parts, obey the applicable local and provincial requirements. For instructions to replace the following parts, please refer to the Assembly Manual for your bike: • AC Adapter • Seat • Seat Post • Front Stabilizer • Rear
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 12
    instructions for the adjustment of the Drive Belt tension on the Schwinn™ 130 / 510U Upright Bikes and 230 / 510R Recumbent Bikes. If you need assistance, please contact Customer Service are necessary, use only genuine Nautilus replacement parts and hardware. Failure to use genuine replacement parts
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 13
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Loosen and remove the Pedals. Note: T he Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 14
    cut the cable by placing the Left Main Shroud close to the side of the machine. NOTICE: Do not pinch or cut the cables. A A A1 6. Using a #2 Phillips Screwdriver, remove the 2 screws that secure the Right Main Shroud. Slowly remove the Right Main Shroud. Set the hardware and Shroud safely aside for
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 15
    7. To test the Drive Belt tension: • Push the Drive Belt downward at the midpoint (M) between the pulleys and measure the distance. The Drive Belt should have only 0.25" (0.64cm) of give. See Figure 1. Figure 1 Or: • Hold the edges of the Drive Belt at the midpoint (M) and twist it (see Figure
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 16
    Flywheel (B), and tape the cardboard to the Brake Magnet. Note: Be sure the cardboard covers all of the Brake Magnet. B C B 9. To loosen the Flywheel hardware (D), use a 15mm open end wrench to hold the nut on one side steady and loosen the nut on the opposite side with a 15mm socket and wrench
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 17
    . Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". (R) (L) 15. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 18
    ) on the Schwinn™ 130 / 510U Bikes NOTICE: This document provides instructions for the calibration of the Brake tension on the Schwinn™ 130 / 510U Upright Bikes. Replacement Procedure Skill Level: II 8027933.021522.A If you need assistance, please contact Customer Service (if purchased
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 19
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Loosen and remove the Pedals. Note: T he Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 20
    3. Flex the edges of the Upper Shroud to disengage the inside tabs from the Main Assembly, and slide it up the Console Mast. 4. Using a 6mm hex wrench, remove the indicated hardware from the Console Mast. Slightly pull the Console Mast upward, and disconnect the cables. Set the hardware, Shroud
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 21
    Left Shroud and place it near the Frame. Set the hardware safely aside for reassembly. NOTICE: Do not pinch or cut the cables. A1 A 7. Using a #2 Phillips Screwdriver, remove the 2 screws that secure the Right Shroud. Slowly remove the Right Main Shroud. Set the hardware safely aside for reassembly
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 22
    . For example only on placing the cardboard. 9. Turn the power on again. Machine is on. Current is active. There is risk of electrical shock. 10. Use the console to set the resistance to the highest level. This moves the Brake Magnet Arm (B1) forward. After the Brake Magnet Arm stops at
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 23
    12. Turn the power on again. Use the console to check the resistance adjustment. C Machine is on. Current is active. There is risk of electrical shock. Note: Before fully attaching the Shrouds,
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 24
    is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". (R) (L) 15. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 25
    instructions for the replacement of the Belt Tensioner Assembly (Idler Assembly) on the Schwinn™ 130 / 510U Upright Bikes and 230 / 510R Recumbent Bikes. If you need assistance, please contact Customer Service , use only genuine Nautilus replacement parts and hardware. Failure to use genuine
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 26
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Loosen and remove the Pedals. Note: T he Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 27
    cut the cable by placing the Left Main Shroud close to the side of the machine. NOTICE: Do not pinch or cut the cables. A A A1 6. Using a #2 Phillips Screwdriver, remove the 2 screws that secure the Right Main Shroud. Slowly remove the Right Main Shroud. Set the hardware and Shroud safely aside for
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 28
    . Be sure to keep fingers clear of all pinch hazards as you turn the Drive Pulley. D 9. Using needlenose pliers, carefully release the spring (F) on the Belt Tensioner (B). 10. Using 13mm wrench and 6mm hex wrench, loosen and remove the Belt Tensioner Hardware (G). Remove the Belt Tensioner
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 29
    Flywheel. Continue to the next step. 15. To loosen the Flywheel hardware (J), use a 15mm open end AJ wrench to hold the nut on one side steady and . Note: This step may require two people. To tighten the Flywheel hardware, use a 15mm open end wrench to hold the nut on one side steady and tighten
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 30
    . Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". (R) (L) 20. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 31
    Assembly on the Schwinn™ 130 / 510U Bikes NOTICE: This document provides instructions for the replacement of the Brake Assembly on the Schwinn™ 130 / 510U Upright Bikes. Replacement Procedure Skill Level: II 8027935.021522.A If you need assistance, please contact Customer Service (if purchased
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 32
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Loosen and remove the Pedals. Note: T he Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 33
    3. Flex the edges of the Upper Shroud to disengage the inside tabs from the Main Assembly, and slide it up the Console Mast. 4. Using a 6mm hex wrench, remove the indicated hardware from the Console Mast. Slightly pull the Console Mast upward, and disconnect the cables. Set the hardware, Shroud
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 34
    the Left Shroud. Disconnect the Power Inlet cable (A1) from the wiring harness (B). NOTICE: Do not pinch or cut the cables. B A1 A 7. Using a #2 Phillips Screwdriver, remove the 2 screws that secure the Right Shroud. Slowly remove the Right Main Shroud. Set the hardware safely aside for reassembly
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 35
    sure the cardboard covers all of the Brake Magnet. C C Note: Your machine does not match the above image. For example only on placing the cardboard. 9. Use the pliers to unhook the Tension Spring (E) from the Main Frame. Pull back and release the Magnet Arm (F) enough to disengage it from the Motor
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 36
    10. Loosen and remove the hex head bolt (H), nut (J) and washer (K) that attach the Brake Assembly (D) to the Main Frame bracket (L). NOTICE: Do not pinch or cut the cables. H L 11. Remove the Brake Assembly (D). Remove the cardboard. Discard the old Brake Assembly. C 12. Installation is the
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 37
    is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". (R) (L) 16. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 38
    on the Schwinn™ 130 / 510U and 230 / 510R Bikes NOTICE: This document provides instructions for the replacement of the Console on the Schwinn™ 130 / 510U and 230 / 510R Bikes. Replacement Procedure Skill Level: II 8027936.020122.A If you need assistance, please contact Customer Service (if
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 39
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 40
    instructions for the replacement of the Console Mast (Upright Handlebar Assembly) on the Schwinn™ 130 / 510U Upright Bikes. If you need assistance, please contact Customer Service parts are necessary, use only genuine Nautilus replacement parts and hardware. Failure to use genuine replacement parts
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 41
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Remove the four screws that attach the Console to the Mast. Carefully lift
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 42
    discard it. 7. Flex the edges of the Upper Shroud to disengage the inside tabs from the Main Assembly, and slide it up the Console Mast. 8. Using a 6mm hex wrench, remove the indicated hardware from the Console Mast. Slightly pull the Console Mast upward, and disconnect the cables. Set the hardware
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 43
    9. Using a 6mm hex wrench, install the Console Mast, Mast Gasket and Top Shroud to the Main Assembly NOTICE: M ake sure the Console Cable does not fall
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 44
    10. Put the Handlebar in the bracket, adjust the Handlebar to the desired angle, and install the T-handle through the holes. NOTICE: Do not pinch or cut the cables 11. Tie the end of the string under the Handlebar Bracket to the end of the HR cable. Carefully pull the cable through the slot under
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 45
    or cut the cables. X4 #2 14. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 46
    instructions for the replacement of the Data Cable (in the Console Mast) on the Schwinn™ 130 / 510U Upright Bikes. If you need assistance, please contact Customer Service parts are necessary, use only genuine Nautilus replacement parts and hardware. Failure to use genuine replacement parts can
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 47
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image to disengage the inside tabs from the Main Assembly, and slide it up the Console Mast. 4. Using a 6mm hex wrench, remove the indicated hardware from the Console Mast. Slightly pull the Console Mast
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 48
    and connect the cable to the Data Cable from the Main Frame. . NOTICE: D o not pinch or cut the cables. This step may require two people. 8. Using a 6mm hex wrench, install the Console Mast, Mast Gasket and Top Shroud to the Main Assembly NOTICE: M ake sure the Console Cable does not fall
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 49
    or cut the cables. X4 #2 10. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 50
    instructions for the replacement of the Drive Belt on the Schwinn™ 130 / 510U Upright Bikes and 230 / 510R Recumbent Bikes. If you need assistance, please contact Customer Service parts are necessary, use only genuine Nautilus replacement parts and hardware. Failure to use genuine replacement parts
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 51
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Loosen and remove the Pedals. Note: T he Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 52
    cut the cable by placing the Left Main Shroud close to the side of the machine. NOTICE: Do not pinch or cut the cables. A A A1 6. Using a #2 Phillips Screwdriver, remove the 2 screws that secure the Right Main Shroud. Slowly remove the Right Main Shroud. Set the hardware and Shroud safely aside for
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 53
    Drive Belt (E) off the Drive Pulley to the outside. Be sure to keep fingers clear of all pinch hazards as you turn the Drive Pulley. D 9. Using needlenose pliers, carefully release the spring (F) on the Belt Tensioner (G). 53 E F G
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 54
    10. To remove the hardware from the Flywheel (H), use the 15mm open end wrench to hold the nut (J) on one side steady and remove the nut on the opposite side with the 15mm socket
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 55
    Flywheel. Continue to the next step. 19. To loosen the Flywheel hardware (J), use a 15mm open end AJ wrench to hold the nut on one side steady and . Note: This step may require two people. To tighten the Flywheel hardware, use a 15mm open end wrench to hold the nut on one side steady and tighten
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 56
    touch at the maximum resistance level. 23. Turn the power on again. Use the console to check the resistance adjustment. Machine is on. Current is strip due to improper installation, then the Pedals can disengage from the bike and/or break while under usage, which can result in serious injury to
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 57
    26. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner's Manual. 57
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 58
    instructions for the replacement of the Drive Pulley (1-piece Crank Assembly) on the Schwinn™ 130 / 510U Upright Bikes and 230 / 510R Recumbent Bikes. If you need assistance, please contact Customer Service necessary, use only genuine Nautilus replacement parts and hardware. Failure to use genuine
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 59
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Loosen and remove the Pedals. Note: T he Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 60
    3. Flex the edges of the Upper Shroud to disengage the inside tabs from the Main Assembly, and slide it up the Console Mast. 4. Using a 6mm hex wrench, remove the indicated hardware from the Console Mast. Slightly pull the Console Mast upward, and disconnect the cables. Set the hardware, Shroud
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 61
    the Left Shroud. Disconnect the Power Inlet cable (A1) from the wiring harness (B). NOTICE: Do not pinch or cut the cables. B A1 A 7. Using a #2 Phillips Screwdriver, remove the 2 screws that secure the Right Shroud. Slowly remove the Right Main Shroud. Set the hardware safely aside for reassembly
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 62
    Drive Belt (B) off the Drive Pulley to the outside. Be sure to keep fingers clear of all pinch hazards as you turn the Drive Pulley. 9. Using needlenose pliers, carefully release the Belt Tensioner Spring (C1) from the hook (D) on the frame. A B D C1 10. Loosen and remove the Locknut (E), Bumper
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 63
    Belt (B) is under the A bearings on the Belt Tensioner (C). 14. Using the needlenose pliers, reattach the Belt Tensioner spring (C1). Make sure that tension is correct. Refer to the "Belt Tension Adjustment" section in this manual. Note: This step may require two people. 15. Installation is the
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 64
    is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". (R) (L) 17. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 65
    on the Schwinn™ 130 / 510U Bikes NOTICE: This document provides instructions for the replacement of the Handlebar Assembly on the Schwinn™ 130 / 510U Upright Bikes. Replacement Procedure Skill Level: II 8027957.021522.A If you need assistance, please contact Customer Service (if purchased
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 66
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Remove the four screws that attach the Console to the Mast. Carefully lift
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 67
    5. Remove the T-handle and washers that attach the Handlebar to the Mast. Set them safely aside for reassembly. NOTICE: H old the Handlebar so that it does not fall. 6. Untie the string from the HR Cable. Remove the old Handlebar and discard it. 7. Put the replacement Handlebar in the bracket,
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 68
    8. Tie the end of the string under the Handlebar Bracket to the end of the HR cable. Carefully pull the cable through the slot under the Handlebar Bracket to the top of the mast. Fully tighten the T-handle to keep the Handlebar in position. Push the cover into position on the Handlebar Bracket.
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 69
    or cut the cables. X4 #2 11. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 70
    instructions for the replacement of the Shrouds on the Schwinn™ 130 / 510U Upright Bikes and 230 / 510R Recumbent Bikes. If you need assistance, please contact Customer Service parts are necessary, use only genuine Nautilus replacement parts and hardware. Failure to use genuine replacement parts can
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 71
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Loosen and remove the Pedals. Note: T he Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 72
    Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". (R) (L) 3. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 73
    instructions for the replacement of the Power Inlet on the Schwinn™ 130 / 510U Upright Bikes and 230 / 510R Recumbent Bikes. If you need assistance, please contact Customer Service parts are necessary, use only genuine Nautilus replacement parts and hardware. Failure to use genuine replacement parts
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 74
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Loosen and remove the Pedals. Note: T he Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 75
    aside for reassembly. Discard the old Console Mast. NOTICE: Do not pinch or cut the cables. This step may require two people. X4 6mm 5. Using a #2 Phillips Screwdriver, remove the 6 screws (indicated) that secure the Left Main Shroud. Remove the bottom screws first, and then the top screws. Set the
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 76
    6. Carefully disconnect the Power Inlet Cable (A1) in the Shroud from Upright bike the wiring harness (B) on the motor. B A1 A Recumbent bike B A1 A A1 A1 Connects to B A 76
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 77
    7. Loosen and remove the thin Nut from the Power Inlet (C) on the outside of the Shroud. C 8. Pull the Power Inlet plug (A) out of the hole toward the inside of the Shroud. Discard the old Power Inlet assembly. 9. Installation is the reverse procedure. NOTICE: Do not pinch or cut the cables. Be sure
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 78
    is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". (R) (L) 12. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 79
    instructions for the replacement of the RPM Sensor (Speed Sensor) on the Schwinn™ 130 / 510U Upright Bikes and 230 / 510R Recumbent Bikes. If you need assistance, please contact Customer Service necessary, use only genuine Nautilus replacement parts and hardware. Failure to use genuine replacement
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 80
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Loosen and remove the Pedals. Note: T he Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 81
    aside for reassembly. Discard the old Console Mast. NOTICE: Do not pinch or cut the cables. This step may require two people. X4 6mm 5. Using a #2 Phillips Screwdriver, remove the 6 screws (indicated) that secure the Left Main Shroud. Remove the bottom screws first, and then the top screws. Set the
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 82
    routing from the RPM Sensor (C) to the wiring harness (B) on your machine. Carefully disconnect the RPM Sensor cable (C1) from the wiring harness. Upright bike 7. Remove the hardware that attaches the RPM Sensor (C) to the Main Frame. Carefully remove the old RPM Sensor and cable and discard it
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 83
    is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". (R) (L) 10. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 84
    Motor on the Schwinn™ 130 / 510U Bikes NOTICE: This document provides instructions for the replacement of the Servo Motor on the Schwinn™ 130 / 510U Upright Bikes. Replacement Procedure Skill Level: II 8027962.021522.A If you need assistance, please contact Customer Service (if purchased in
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 85
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Loosen and remove the Pedals. Note: T he Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 86
    3. Flex the edges of the Upper Shroud to disengage the inside tabs from the Main Assembly, and slide it up the Console Mast. 4. Using a 6mm hex wrench, remove the indicated hardware from the Console Mast. Slightly pull the Console Mast upward, and disconnect the cables. Set the hardware, Shroud
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 87
    the Left Shroud. Disconnect the Power Inlet cable (A1) from the wiring harness (B). NOTICE: Do not pinch or cut the cables. B A1 A 7. Using a #2 Phillips Screwdriver, remove the 2 screws that secure the Right Shroud. Slowly remove the Right Main Shroud. Set the hardware safely aside for reassembly
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 88
    8. Insert 2.5" x 10" cardboard between the Brake Magnet (C) and the Flywheel (C), and tape the cardboard to the Brake Magnet. Note: Be sure the cardboard covers all of the Brake Magnet. C C D Note: Your machine does not match the above image. For example only on placing the cardboard. 9. Observe the
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 89
    through the Frame. Remove the zipties that attach the lower Console Cable to the Frame. F 11. Untie the string from the Console Cable (F). H 12. Use the pliers to unhook the Tension Spring (G) from the Main Frame. Pull back and release the Magnet Arm (J) enough to disengage it from the Motor
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 90
    any cables. 20. Turn the power on. by plugging in the machine. Machine is on. Current is active. There is risk of electrical shock. 21. Use the console to set the resistance to the highest level. Unplug the machine. Disconnect all power and allow to sit for 5 minutes. 22. If correctly
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 91
    is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". (R) (L) 25. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 92
    the Shrouds on the Schwinn™ 130 / 510U Bikes NOTICE: This document provides instructions for the replacement of the Shrouds on the Schwinn™ 130 / 510U Upright Bikes. Replacement Procedure Skill Level: II 8027963.021522.A If you need assistance, please contact Customer Service (if purchased in
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 93
    Disconnect all power to the machine before you service it. Note: Your machine may not match the image. For reference only. 1. Loosen and remove the Pedals. Note: T he Left Pedal is reverse-threaded. Orientation is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 94
    3. Flex the edges of the Upper Shroud to disengage the inside tabs from the Main Assembly, and slide it up the Console Mast. 4. Using a 6mm hex wrench, remove the indicated hardware from the Console Mast. Slightly pull the Console Mast upward, and disconnect the cables. Set the hardware, Shroud
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 95
    the Left Shroud. Disconnect the Power Inlet cable (A1) from the wiring harness (B). NOTICE: Do not pinch or cut the cables. B A1 A 7. Using a #2 Phillips Screwdriver, remove the 2 screws that secure the Right Shroud. Slowly remove the Right Main Shroud. Set the hardware safely aside for reassembly
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 96
    is based from a seated position on the bike. The Left Pedal has an "L", the Right Pedal an "R". (R) (L) 10. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 97
    instructions for the replacement of the Transport Wheels on the Schwinn™ 130 / 510U Upright Bikes and 230 / 510R Recumbent Bikes. If you need assistance, please contact Customer Service are necessary, use only genuine Nautilus replacement parts and hardware. Failure to use genuine replacement parts
  • Schwinn 130 Upright Bike 2020 model | Service Manual - Page 98
    the end of the Front Stabilizer. 3. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
1
Schwinn
™
130 / 510U (Model Year 2020)
Upright Bike Service Manual
8027919.021522.A
Service Manual
Table of Contents
8027930.021522.A
TM
Nautilus, Inc., www.NautilusInc.com, 5415 Centerpoint Parkway, Groveport, OH 43125
U.S.A. - Customer Service: North America (800) 605-3369, [email protected] | outside U.S. www.nautilusinternational.com |
Printed in China | © 2022 Nautilus, Inc. | Schwinn and the Schwinn logo are trademarks owned or licensed by Nautilus, Inc., registered or otherwise protected by common law in the United States and other nations.
|
ORIGINAL DOCUMENT - ENGLISH VERSION ONLY
Section Code
Section
Page Number
1
Important Safety Instructions
2
1
Safety Warning Labels and Serial Number
3
1
FCC Compliance
3
1
Specifications
4
1
Maintenance
5
1
Moving the Bike
6
1
Leveling the Bike
6
1
Connectivity
7
1
Troubleshooting
8
1
Maintenance Parts Exploded View
10
1
Replacement Procedure Skill Level
11
Mechanical Procedures
2
Adjust the Belt Tension
12
3
Set the Brake Tension (Calibration)
18
Part Replacement
4
Belt Tensioner Assembly (Idler Assembly)
25
5
Brake Assembly
31
6
Console
38
7
Console Mast (Upright Handlebar Assembly)
40
8
Data Cable in the Mast
46
9
Drive Belt and Flywheel Assembly
50
10
Drive Pulley Assembly (Crank Assembly)
58
11
Handlebar Assembly
65
12
Pedals
70
13
Power Inlet
73
14
RPM Sensor (Speed Sensor)
79
15
Servo Motor
84
16
Shrouds
92
17
Transport Wheels
97