Schwinn 130 Upright Bike 2020 model Service Manual - Page 22

the Brake Magnet Arm B1 forward. After the Brake Magnet Arm stops

Get Schwinn 130 Upright Bike 2020 model PDF manuals and user guides View all Schwinn 130 Upright Bike 2020 model manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

8. Insert 2.5" x 10" cardboard between the Brake Magnet (B) and the Flywheel (C), and tape the cardboard to the Brake Magnet. Note: Be sure the cardboard covers all of the Brake Magnet. C Note: Your machine does not match the above image. For example only on placing the cardboard. 9. Turn the power on again. Machine is on. Current is active. There is risk of electrical shock. 10. Use the console to set the resistance to the highest level. This moves the Brake Magnet Arm (B1) forward. After the Brake Magnet Arm stops at the highest resistance level, turn power off. Disconnect all power and allow to sit for 5 minutes. 11. To adjust the Brake tension, loosen the 2 hex head bolts (E) and move the Servo Motor assembly (D) until the closest point on the Brake Magnet (B) is within 3.0 mm (1/8") of the Flywheel (C). Tighten the bolts. Note: If the cardboard is not 3mm (1/8") thick, you can use the pages of a paperback book to measure the gap. Approximately 36 pages (sheets) = 3mm. B C 22 B1 E D B

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
22
8.
Insert 2.5” x 10” cardboard between the Brake Magnet (B) and the
Flywheel (C), and tape the cardboard to the Brake Magnet.
Note:
Be sure the cardboard covers all of the Brake Magnet.
9.
Turn the power on again.
Machine is on. Current is active. There is risk of electrical
shock.
10.
Use the console to set the resistance to the highest level. This moves
the Brake Magnet Arm (B1) forward. After the Brake Magnet Arm stops at
the highest resistance level, turn power off.
Disconnect all power and allow to sit for 5 minutes.
11.
To adjust the Brake tension, loosen the 2 hex head bolts (E) and
move the Servo Motor assembly (D) until the closest point on the Brake
Magnet (B) is within 3.0 mm (1/8”) of the Flywheel (C). Tighten the bolts.
Note:
If the cardboard is not 3mm (1/8”) thick, you can use
the pages of a paperback book to measure the gap.
Approximately 36 pages (sheets) = 3mm.
Note:
Your machine does not match the above image. For
example only on placing the cardboard.
C
B
C
B
D
E
B1