Schwinn 130 Upright Bike 2020 model Service Manual - Page 89

Remove the Servo Motor M. Discard the old Servo Motor.

Get Schwinn 130 Upright Bike 2020 model PDF manuals and user guides View all Schwinn 130 Upright Bike 2020 model manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

10. Tie the length of string to the end of the lower Console Cable (F) at the top of the Mast mount. Pull the cable and string down through the hole (H) on the side of the Frame so that the string extends through the Frame. Remove the zipties that attach the lower Console Cable to the Frame. F 11. Untie the string from the Console Cable (F). H 12. Use the pliers to unhook the Tension Spring (G) from the Main Frame. Pull back and release the Magnet Arm (J) enough to disengage it from the Motor Pulley Shaft (K). 13. Loosen and remove the two hex head bolts (L) from the Servo Motor (M). 14. Remove the Servo Motor (M). Discard the old Servo Motor. NOTICE: Do not touch the Potentiometer (P). Do not pinch or cut the cables. P 15. Install the new Servo Motor to the Main Assembly. 89 G JK L M

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
89
10.
Tie the length of string to the end of the lower Console Cable (F) at
the top of the Mast mount. Pull the cable and string down through the
hole (H) on the side of the Frame so that the string extends through the
Frame.
Remove the zipties that attach the lower Console Cable to the
Frame.
11.
Untie the string from the Console Cable (F).
12.
Use the pliers to unhook the Tension Spring (G) from the Main
Frame. Pull back and release the Magnet Arm (J) enough to disengage it
from the Motor Pulley Shaft (K).
13.
Loosen and remove the two hex head bolts (L) from the Servo Motor
(M).
14.
Remove the Servo Motor (M). Discard the old Servo Motor.
NOTICE:
Do not touch the Potentiometer (P). Do not pinch or cut
the cables.
15.
Install the new Servo Motor to the Main Assembly.
P
F
H
G
K
J
M
L