Sharp DT-200L Operation Manual - Page 16

Operating the Remote Control

Get Sharp DT-200L PDF manuals and user guides View all Sharp DT-200L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Setup & Connections Connecting to a Computer Connecting a computer with DIGITAL RGB output 1 Slide the "DIGITAL INPUT TYPE" switch on the back terminal board to "PC". 2 Connect one of the DVI cable (commercially available) to the DIGITAL INPUT port on the projector. 3 Connect the other end to the Corresponding terminal on a computer. • Make sure to turn both the projector and the video equipment off, before switching the "DIGITAL INPUT TYPE" swich and connecting. 3 DVI cable (commercially available) 2 1 • Refer to "Computer Compatibility Chart" on page 51 for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions not to work. • The arrows (→, ↔) in the configuration above indicate the direction of the signals. • A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Sharp Authorized Service Center or Dealer. Operating the Remote Control Remote Control 23Ј (7 m) 30˚ 45˚ 30˚ The remote control can be used to control the projector within the range shown on the left. • The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ due to the screen material. DT-200 45˚ 30˚ Remote Control E-15 DT-200(E)#p15_21.p65 15 02.11.21, 11:30 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
E-15
Setup & Connections
Operating the Remote Control
The remote control can be used to control the projec-
tor within the range shown on the left.
• The signal from the remote control can be reflected off a
screen for easy operation. However, the effective distance
of the signal may differ due to the screen material.
Remote Control
Remote Control
45˚
23
±
(7 m)
30˚
30˚
45˚
30˚
Connecting a computer with DIGITAL RGB output
1
Slide the “DIGITAL INPUT TYPE” switch on the back terminal board to “PC”.
2
Connect one of the DVI cable (commercially available) to the DIGITAL INPUT port on the projector.
3
Connect the other end to the Corresponding terminal on a computer.
• Make sure to turn both the projector and the video equipment off, before switching the “DIGITAL INPUT TYPE”
swich and connecting.
•
Refer to “Computer Compatibility Chart” on page 51 for a list of computer signals compatible with the projector. Use with computer
signals other than those listed may cause some of the functions not to work.
•
The arrows (
→
,
↔
) in the configuration above indicate the direction of the signals.
•
A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Sharp Authorized Service Center or
Dealer.
2
3
1
Connecting to a Computer
DVI cable
(commercially available)
DT-200(E)#p15_21.p65
02.11.21, 11:30 AM
15