Sharp FP-R65CX Operation Manual - Page 20

Mist Unit

Get Sharp FP-R65CX PDF manuals and user guides View all Sharp FP-R65CX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

CARE AND MAINTENANCE The frequency of maintenance (descaling) will depend on the hardness of the water that you use; the harder the water the more often descaling will be necessary. MIST UNIT 1 Preparing the descaling solution. Citric acid, available at some drugstores, or 100% bottled lemon juice are used for descaling. Choose one to use, and prepare the descaling solution. Dissolve 3 teaspoon of citric acid and 600 ml of luke-warm water in some suitable container, and stir well. Use only bottled 100% lemon juice with no pulp (please check before using and strain through a fine strainer if you are not sure). Pour 50 ml of lemon juice and 600 ml of luke-warm water in some suitable container, and stir well. 2 Presoak a mist filter set in the solution prior to cleaning. When using lemon juice, it is recommended to presoak longer than citric acid. MIST Filter Set Do not take the MIST Filter out of MIST Filter Frame. If a MIST Filter is taken out of the Frame by mistake, put it back in the frame, by following the procedures shown in the diagram below. MIST Filter Antibacterial Sheet MIST Filter Frame 3 Rinse the MIST Filter set with water. • Change the water and repeat this procedure 2-3 times. • Use clean water each time. • Inadequate rinsing may cause citric acid odour or changes in the shape/ colour of the main unit. 4 Wash inside the tray with water to remove impurities. • Do not remove the float (Styrofoam). • Clean difficult-toreach parts with a cotton swab or tooth brush. 5 Put the MIST tray cap back on to close it. Make sure that the cap is closed by pushing the whole circumference of the cap. Failing to close the cap completely may result in water spills. MIST Tray MIST Tray Cap 6 Attach the MIST Filter set to the MIST Tray. MIST Filter Set MIST Tray 7 Put back the MIST Tray set and MIST Tray in the Main Unit. 8 Plug in the product and press the MIST Unit Reset Button on the main unit. MIST Filter Reset Button Replacement Filter See Page E-21 TANK With a small amount of water inside and the tank cap closed, wash the mist tray set by shaking it. When using a kitchen detergent, dilute the detergent with water and rinse it thoroughly. Tank E-18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
E-18
CARE AND MAINTENANCE
MIST UNIT
TANK
1
5
2
3
4
6
7
8
Preparing
the
descaling
solution.
MIST Filter Set
MIST Filter
Antibacterial Sheet
MIST Filter Frame
MIST Tray Cap
MIST Tray
MIST Filter Set
MIST Tray
MIST Filter
Reset Button
Replacement Filter
See Page E-21
Tank
Citric acid, available at some
drugstores, or 100% bottled lemon juice
are used for descaling.
Choose one to
use, and prepare the descaling solution.
<For using citric acid>
Dissolve 3 teaspoon of citric acid and 600 ml of
luke-warm water in some suitable container, and
stir well.
<For using lemon juice>
Use only bottled 100% lemon juice with no pulp
(please check before using and strain through
a fine strainer if you are not sure). Pour 50 ml
of lemon juice and 600 ml of luke-warm water
in some suitable container, and stir well.
Presoak a mist filter set in the
solution prior to cleaning.
When using lemon juice, it
is
recommended
to
presoak longer than citric
acid.
Do not take the MIST Filter out of MIST
Filter Frame. If a MIST Filter is taken
out of the Frame by mistake, put it back
in the frame, by following the procedures
shown in the diagram below.
Rinse the MIST Filter set with
water.
• Change the water and repeat this
procedure 2-3 times.
• Use clean water each time.
• Inadequate rinsing may
cause citric acid odour or
changes in the shape/
colour of the main unit.
Wash inside the tray with water
to remove impurities.
• Do not remove the
float (Styrofoam).
• Clean difficult-to-
reach parts with a
cotton swab or
tooth brush.
Put the MIST tray cap back on
to close it.
Make sure that the cap is closed by
pushing the whole circumference of the
cap. Failing to close the cap completely
may result in water spills.
Attach the MIST
Filter set to the
MIST Tray.
Put back the MIST Tray set and
MIST Tray in the Main Unit.
Plug in the product and press
the MIST Unit
Reset Button on
the main unit.
With a small amount of water inside and the tank cap closed, wash
the mist tray set by shaking it.
When using a kitchen detergent, dilute the detergent with water and
rinse it thoroughly.
The frequency of maintenance (descaling) will depend on the hardness of the water that you
use; the harder the water the more often descaling will be necessary.