Sharp FP-R65CX Operation Manual - Page 22

Main Unit, Pre-filter, Sensors

Get Sharp FP-R65CX PDF manuals and user guides View all Sharp FP-R65CX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

CARE AND MAINTENANCE MAIN UNIT To prevent dirt or stains on the main unit, clean as often as necessary. If stains are allowed to remain, they may become hard to clean. Wipe with a dry, soft cloth For stubborn stains or dirt, use a soft cloth dampened with warm water. Do not use volatile fluids Benzene, paint thinner, polishing powder, etc., may damage the surface. Do not use detergents Detergent ingredients may damage the unit. Keep the unit away from water PRE-FILTER As shown in a figure, clean the top surface of the Pre- Filter lightly with a vacuum cleaner. When Pre-Filter is very dirty, wash it in water with mild kitchen detergent and dry Pre-Filter well in the shade. Pre-Filter SENSORS (DUST SENSOR, ODOUR SENSOR, TEMPERATURE/HUMIDITY SENSOR) Remove dust from the surface of the hole of the sensors using a vacuum cleaner. SENSOR FILTER CARE (The sensor Filter is in the sensor cover.) (Detach the sensor filter and tap it lightly with your hand to remove the dust. If it is very dirty, wash it with water and then allow it to dry thoroughly. Hole of Temperature/Humidity Sensor Hole of Odour Sensor Sensor Cover Sensor Cover Sensor Filter It does not have a front and a back. Hole of Dust Sensor E-20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
E-20
CARE AND MAINTENANCE
To prevent dirt or stains on the main unit, clean as often as necessary. If stains are allowed to
remain, they may become hard to clean.
Wipe with a dry, soft cloth
For stubborn stains or dirt, use a soft cloth dampened with warm water.
Do not use volatile fluids
Benzene, paint thinner, polishing powder, etc., may damage the surface.
Do not use detergents
Detergent ingredients may damage the unit.
Keep the unit away from water
MAIN UNIT
PRE-FILTER
Pre-Filter
SENSORS
(DUST SENSOR, ODOUR SENSOR, TEMPERATURE/HUMIDITY SENSOR)
Hole of Odour Sensor
Sensor Cover
Hole of Temperature/Humidity Sensor
Hole of Dust Sensor
As shown in a figure, clean the top surface of the
Pre- Filter lightly with a vacuum cleaner.
When Pre-Filter is very dirty, wash it in water with
mild kitchen detergent and dry Pre-Filter well in
the shade.
Remove dust from the surface of the hole of the
sensors using a vacuum cleaner.
SENSOR FILTER CARE
(The sensor Filter is in the sensor cover.)
(Detach the sensor filter and tap it lightly with your
hand to remove the dust.
If it is very dirty, wash it with water and then allow it
to dry thoroughly.
Sensor Filter
It does not have a front and
a back.
Sensor Cover