Sharp LC-70LE650U Operation Manual - Page 18

Direct Button Operation Changing Channels You can change channels in several ways. Method 1 Using CHU/V on the remote control unit or on the TV. Method 2 Using remote control buttons 0-9, • (DOT). Examples: To select a 1 or 2-digit channel number (e. g., Channel 5): Press 5 ENT. To select a 3-digit channel number (e. g., Channel 115): Press 1 1 5 ENT. To select a 4-digit channel number (e. g., Channel 22.1): Press 2 2 • (DOT) 1 ENT. Method 3 Selecting the program from the Channel list. 1 Press INPUT on the remote control unit. • The INPUT list displays. 2 Press c/d to select "AIR" or "CABLE". • The Channel list displays. 3 Press a/b to select the desired channel, and then press ENTER. NOTE • When selecting a 1-digit channel number, it is not necessary to press 0 before the number. • When you enter 0-9 only, channel selection will be made if there is no operation within a few seconds. • If you push "0" by itself, nothing will happen. • Complete the above steps within a few seconds. • When you enter 0-9 and • (DOT), channel selection will be made if there is no operation within a few seconds. Changing Volume You can change the volume by pressing VOLk/l on the TV or on the remote control unit. • To increase the volume, press VOLk. • To decrease the volume, press VOLl. 30 Audio status Output device Speaker Output Select Fixed Variable Variable sound Mute • When "Output Select" is set to "Variable", the indicator on the screen changes as shown below. 100 MUTE Mutes the current sound output. Press MUTE. • " " will be displayed on the screen for 30 minutes, and the sound is silenced. NOTE • Within 30 minutes of pressing MUTE, mute can be canceled by pressing VOLk/l or MUTE. • Mute will be canceled after 30 minutes have passed. However, the TV will not suddenly output a loud sound as the volume level is set to 0 automatically. FREEZE Allows you to capture and freeze a moving image that you are watching. Press FREEZE. • A moving image is captured. • Press FREEZE again to cancel the function. NOTE • When this function is not available, "No displaying still image available." will display. • The still image automatically goes out after 30 minutes. • If you are using the freeze function and a broadcast activates the V-CHIP BLOCK, the freeze function will be canceled and a V-CHIP BLOCK message will appear. • You can have the same settings by choosing "Freeze" on the menu items. (See page 24.) INPUT To view external source images, select the input source by pressing INPUT on the remote control unit or on the TV. 1 Press INPUT. • The INPUT list screen displays. 2 Press a/b or press INPUT again to select the input source. • An image from the selected source automatically displays. • Each time INPUT is pressed, the input source toggles. • If the corresponding input is not plugged in, you cannot change the input. Be sure to connect the equipment beforehand. NOTE • See pages 11 to 13 and 39 for external equipment connection. FLASHBACK Press FLASHBACK to switch to the previously tuned channel or previous input mode. • Press FLASHBACK again to switch back to the currently tuned channel. NOTE • FLASHBACK will not work if no channel has been changed after the TV is turned on. SmartCentral Allows you to directly activate various types of applications. 1 Press SmartCentral to display the application window. • Press SmartCentral again to display a list of applications by category. 2 Press c/d(or a/b) to select the desired application, and then press ENTER. • If you changed the display to the list of applications in step 1, select a category and then an application. See page 47 for details. • If " " is displayed after you switch to USB mode, check the USB connection. • If " " or " " is displayed after you switch to Home Network (DLNA) mode or after you connect to the Internet, check your TV's network settings and connection. NOTE • See pages 34, 45 to 47 for details of viewable applications. • You can display the application window by choosing "APPS" on the menu items. (See page 24.) • When this function is not available, "Can not operate this function now" will display. NOTE • See page 25 for details on the Output Select function. 16