Sharp LC-70LE650U Operation Manual - Page 33

Enjoying 3D Image Viewing (for the LE857U, LE757U, LE755U and LE657U models) Display Methods for 3D and 2D Images Display method Example display Description 2D ➝ 3D • Converts normal 2D images into 3D images. 3D mode (using the Side by Side 3D Glasses) Top and Bottom 2D mode (without using the 3D Glasses) Side by Side ➝ 2D Top and Bottom ➝ 2D • Creates 3D images from 3D images displayed side by side. The image is split into a left and right image, and then the images are stretched and displayed sequentially to create a 3D image. • Creates 3D images from 3D images displayed on the top and bottom. The image is split into a top and bottom image, and then the images are stretched and displayed sequentially to create a 3D image. • Creates 2D images from 3D images displayed side by side. Only the left image is stretched and displayed. The image does not appear in 3D. • Creates 2D images from 3D images displayed on the top and bottom. Only the top image is stretched and displayed. The image does not appear in 3D. Viewing 3D Images NOTE • The TV screen may temporarily become black when the TV is trying to detect a 3D image signal and when switching from 3D to 2D mode. Receiving a 3D Image Signal That Can Be Detected Automatically The image signal may contain a 3D identification signal. You can enable the TV to automatically detect the 3D image type by selecting "System Options" > "3D Setup" > "3D Auto Change" on the TV. (See page 32.) 1 When "3D Auto Change" is set to "Mode 1" or "Mode 2" • The 3D image type is detected automatically and the appropriate 3D image is displayed. Changed to 3D mode. Power on the 3D glasses then put them on. If you are in bad physical conditions or feel uncomfortable watching 3D picture please stop watching monitor. Ending 3D Image Viewing 5 Take off the 3D Glasses and turn off the power. NOTE • If the input signal switches to 2D, 2D images are displayed automatically. • 3D mode is canceled automatically when the setting is changed, input selection is changed, or the power is turned off. Receiving a 3D Image Signal That Cannot Be Detected Automatically 1 Press 3D. • A screen appears prompting you to select between 3D and 2D image viewing. 2 Press c/d to select "3D" or "2D", and then press ENTER. • To view in 3D mode: Select "3D", and then go to step 3. • To view in 2D mode: Select "2D", and then go to step 6. 3 Press c/d to select the 3D signal type ("2D➝3D", "Side by Side" or "Top and Bottom") and then press ENTER. 3D When "3D Auto Change" is set to "Off" • The following message is displayed. Press 3D. 3D picture is detected. Power on the 3D glasses. (Need to wear the 3D glasses to watch 3D picture) • Press c/d to select the "Yes", and then press ENTER. 2 Turn on the 3D Glasses and place them on your head. 3 You can now view 3D images. Switching from 3D to 2D Mode 4 Press 3D during the 3D mode. Select "Yes" and press ENTER to switch to 2D mode. • Take off the 3D Glasses and turn off the power. 2D -> 3D Side by Side Top and Bottom • If you select the same system as that of the input signal, 3D images are displayed. 4 Turn on the 3D Glasses and place them on your head. 5 You can now view 3D images. Switching from 3D to 2D Mode 6 Press c/d to select the 2D signal type ( "Side by Side" or "Top and Bottom") and then press ENTER. Side by Side Top and Bottom • If you select the same system as that of the input signal, 2D images are displayed. • Take off the 3D Glasses and turn off the power. Ending 3D Image Viewing 7 Take off the 3D Glasses and turn off the power. 31