Sharp LC-70LE650U Operation Manual - Page 51

Appendix - stand

Get Sharp LC-70LE650U PDF manuals and user guides View all Sharp LC-70LE650U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Appendix Attaching the Stand (for the 80 Inch Models) Building the Work Table Before attaching the stand to the TV, build a work table on which to rest the TV. • To build the table, use the cushioning materials used in the packaging. • Of the cushioning materials used, TOP-C is also used during stand unit assembly. Be sure to assemble the stand unit before building the work table. TOP-L TOP-R TOP-C FRONT • Before attaching (or detaching) the stand, unplug the AC cord. • Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged. CAUTION • Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over. ■ LC-80LE857U 1 Confirm that there are 14 screws (8 long screws, 4 middle screws and 2 short screws) supplied with the stand unit. 2 Attach the supporting post for the stand unit onto the base as shown below. • The supporting post attaches to the base at an offcentered location on the base. Be sure to attach the supporting post in the direction indicated below and attach the stand to the TV with the wider side of the base facing forward. 6 1Insert the stand cover. 2 Insert the screw to secure the stand cover. Short screws 1 Insert each of the cushioning materials in the respective directions shown in the figure. • Insert TOP-L and TOP-R into the left and right sides of the case respectively. • Insert TOP-C to fit between the lines on the other side of the case. TOP-R TOP-L CASE LINE 3 After you have built the work table, spread a blanket or similar soft cloth over the table and then lay the TV display down on the covered table before attaching the stand to the TV. • Do not use a small table for this. • Refer to the operation manual for information on attaching the stand. Long screws 3 Build the work table. 4 Insert the stand into the openings on the rear of the TV. • Make sure that the stand is firmly inserted into the TV. Improper installation may result in tilting of the TV set. Soft cushion TOP-C 2 The case is equipped with push-in tabs to hold the cushioning materials in place. Push in the tabs (2 for each location) to secure the cushioning materials in the case. Push-in tabs 5 Insert and tighten the 4 screws into the 4 holes on the rear of the stand unit. Middle screws 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
49
Appendix
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from
being damaged.
CAUTION
•
Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
■
LC-80LE857U
1
Confirm that there are 14 screws (8 long screws,
4 middle screws and 2 short screws) supplied
with the stand unit.
2
Attach the supporting post for the stand unit
onto the base as shown below.
• The supporting post attaches to the base at an
offcentered location on the base. Be sure to attach
the supporting post in the direction indicated
below and attach the stand to the TV with the
wider side of the base facing forward.
Long screws
3
Build the work table.
4
Insert the stand into the openings on the rear of
the TV.
• Make sure that the stand is firmly inserted into the TV.
Improper installation may result in tilting of the TV set.
Soft cushion
5
Insert and tighten the 4 screws into the 4 holes
on the rear of the stand unit.
Middle screws
6
1
Insert the stand cover.
2
Insert the screw to secure the stand cover.
Short screws
Attaching the Stand (for the 80 Inch Models)
Building the Work Table
Before attaching the stand to the TV, build a work table on which to rest the TV.
• To build the table, use the cushioning materials used in the packaging.
• Of the cushioning materials used, TOP-C is also used during stand unit assembly. Be sure to assemble the
stand unit before building the work table.
FRONT
TOP-L
TOP-R
TOP-C
1
Insert each of the cushioning materials in the
respective directions shown in the figure.
• Insert TOP-L and TOP-R into the left and right
sides of the case respectively.
• Insert TOP-C to fit between the lines on the other
side of the case.
TOP-L
CASE
LINE
TOP-R
TOP-C
2
The case is equipped with push-in tabs to
hold the cushioning materials in place. Push
in the tabs (2 for each location) to secure the
cushioning materials in the case.
Push-in tabs
3
After you have built the work table, spread a
blanket or similar soft cloth over the table and
then lay the TV display down on the covered
table before attaching the stand to the TV.
• Do not use a small table for this.
• Refer to the operation manual for information on
attaching the stand.