Singer 14T968DC PROFESIONAL 5 Instruction Manual 31 - Page 22

Overedge Right Needle

Get Singer 14T968DC PROFESIONAL 5 PDF manuals and user guides View all Singer 14T968DC PROFESIONAL 5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Turn the hand wheel toward you until the chain stitch looper extends out 10mm from the needle plate edge. Thread the looper area of the machine following the brown color-coded thread guides 4~11. Note: Use the tweezers provided in the accessory case to aid in threading the looper. Place the thread with the point of the tweezers through threading guide 4. Place the thread with the point of the tweezers through the front slot of threading guide 5. 4 5 9 6 7 8 Thread the looper eye (A) from front to back. Pull about 10cm (4 inches) of thread through the looper. Position thread into V cutout (B) on threader. Firmly hold thread tail with left hand and pull threader lever (C) up into place (D). 10 A 11 D B 4) Threading the Overedge Right Needle (Blue) (B on needle clamp) Thread the right needle as indicated 1~9. Raise Presser foot by lowering presser bar lifter to release Tension discs. 21 C 1 6 7 85 2 3 4 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
9
2
7
5
8
6
4
3
1
10
11
8
7
9
6
4
5
C
A
B
D
21
Thread the right needle as indicated 1~9.
Turn the hand wheel toward you until the chain stitch
looper extends out 10mm from the needle plate
edge.
Thread the looper area of the machine following
the brown color-coded thread guides 4~11.
Place the thread with the point of the tweezers
through threading guide 4.
Place the thread with the point of the tweezers
through the front slot of threading guide 5.
Thread the looper eye (A) from front to back.
Pull about 10cm (4 inches) of thread through the
looper. Position thread into V cutout (B) on
threader. Firmly hold thread tail with left hand
and pull threader lever (C) up into place (D).
Raise Presser foot
to release Tension discs.
by lowering presser bar lifter
Note: Use the tweezers provided in the accessory
case to aid in threading the looper.
4) Threading the
(Blue)
Overedge Right Needle
(B on needle clamp)