Home » Sony Manuals » Audio Components » Sony STR-DA5300ES » Manual Viewer

Sony STR-DA5300ES Operating Instructions (Large File - 21.32 MB) - Page 142

Tuner, Remote control, Recording cannot be carried out.

Add to My Manuals
Save this manual to your list of manuals

Page 142 highlights

are output from the VIDEO jack. Input 480i component video signals. • When component input signals other than 480p are output, use the COMPONENT VIDEO OUT jack and set "Resolution" to "DIRECT." Images of the source with HDMI connection is not output to the TV. • Make sure that cables are correctly and securely connected to components. • Depending on the playback component, component may need to be set up. Refer to the operating instructions supplied with the each component. • Be sure to use a connecting cable for the HDMI jack corresponding to high speed (an HDMI version1.3a, category 2 cable) when you view images or listen to sound during a DeepColor transmission. Recording cannot be carried out. • Check that the components are connected correctly (page 27). • Select the source component using INPUT SELECTOR (page 53). The GUI does not appear on the TV screen. • Press SHIFT, then press MENU to show "GUI MODE" on the display. • Check the TV is connected correctly. Tuner The FM reception is poor. • Use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna (aerial) as shown below. If you connect the receiver to an outdoor antenna (aerial), ground it against lightning. To prevent a gas explosion, do not connect the ground (earth) wire to a gas pipe. 142GB Outdoor FM antenna (aerial) Receiver Ground (earth) wire (not supplied) To ground Radio stations cannot be tuned in. • Check that the antennas (aerials) are connected securely. Adjust the antennas (aerials) and connect an external antenna (aerial), if necessary. • Keep the satellite radio antenna, away from the speaker cords and the power cord to avoid picking up noise. • The signal strength of the stations is too weak (when tuning in with automatic tuning). Use direct tuning. • Make sure you set the tuning interval correctly (when tuning in AM stations with direct tuning). • No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations). Preset the stations (page 84). • Press DISPLAY so that the frequency appears on the display. The system cannot receive satellite channels at all. • The receiving condition is not good. Move the antenna to the place where the condition is good. • Check that you subscribed to the desired satellite radio service (see page 85). Remote control The remote does not function. • Point the remote at the remote sensor on the receiver.

Section	Page
GB	2
Table of Contents	4
Getting Started	6
Description and location of parts	6
1: Installing speakers	16
2: Connecting speakers	18
3: Connecting the monitor	20
4a: Connecting the audio components	22
4b: Connecting the video components	27
5: Connecting the antennas (aerials)	38
6: Preparing the receiver and the remote	39
7: Operating the receiver using the GUI (Graphical User Interface)	41
8: Setting the speakers	44
9: Calibrating the appropriate speaker settings automatically (Auto Calibration)	46
Playback	53
Selecting a component	53
Listening to a Super Audio CD/CD	55
Watching a DVD/Blu-ray Disc	56
Enjoying video games	57
Watching video	58
Amplifier Operations	59
Settings for the audio (Audio settings menu)	59
Settings for the video (Video settings menu)	60
Settings for HDMI (HDMI menu)	60
Settings for the system (System settings menu)	61
Enjoying Surround Sound	62
Enjoying a pre- programmed sound field	62
Adjusting the sound effect	69
Using the surround back decoding mode	71
Enjoying the surround effect at low volume levels (NIGHT MODE)	73
Advanced Speakers Setting Up	74
Adjusting the speaker settings manually	74
Adjusting the equalizer	80
Tuner Operations	82
Listening to FM/AM radio	82
Listening to satellite radio	85
Other Operations	94
Converting analog video input signals	94
Using the DIGITAL MEDIA PORT adapter	94
Naming inputs	98
Switching between digital and analog audio (INPUT MODE)	99
Enjoying the sound/ images from other inputs	100
Changing the display	102
Using the sleep timer	106
Recording using the receiver	107
Listening to the sound in another zone (ZONE 2/ZONE 3 operations)	108
Using a bi-amplifier connection	113
Using the CONTROL S Control System	114
Operating without connecting to the TV	115
Using the Remote	125
Operating each component using the remote	125
Programming the remote	127
Performing several commands in sequence automatically (Macro Play)	130
Setting remote control codes that are not stored in the remote	132
Clearing all the contents of the remote’s memory	134
Additional Information	135
Glossary	135
Precautions	138
Troubleshooting	139
Specifications	143
Index	146
FR	150
Table des matières	152
Mise en service	154
Description et emplacement des pièces	154
1: Installation des enceintes	165
2: Raccordement des enceintes	167
3: Raccordement de l’écran	169
4a: Raccordement des appareils audio	171
4b: Raccordement des appareils vidéo	177
5: Raccordement des antennes	188
6: Préparation de l’ampli- tuner et de la télécommande	189
7: Utilisation de l’ampli- tuner à l’aide de GUI (Graphical User Interface)	192
8: Réglage des enceintes	195
9: Calibrage automatique aux réglages appropriés (Auto Calibration)	197
Lecture	204
Sélection d’un appareil	204
Écoute d’un Super Audio CD/CD	206
Lecture d’un DVD/Blu-ray Disc	207
Utilisation d’une console de jeux vidéo	208
Lecture d’une cassette vidéo	209
Opérations de l’amplificateur	210
Paramètres pour l’audio (Menu de paramétrage Audio)	210
Paramètres pour la vidéo (Menu de paramétrage Video)	211
Paramètres pour HDMI (Menu HDMI)	211
Paramètres pour le système (Menu de paramétrage System)	212
Écoute du son surround	213
Écoute d’un champ sonore préprogrammé	213
Sélection de l’effet sonore	221
Utilisation du mode de décodage du son surround arrière	223
Écoute du son surround à faible volume (NIGHT MODE)	225
Paramétrage avancé des enceintes	227
Réglage manuel des paramètres d’enceintes	227
Réglages de l’égaliseur	234
Opérations du tuner	236
Écoute de stations de radio FM/AM	236
Écoute de la radio satellite	240
Autres opérations	251
Conversion de signaux d’entrée vidéo analogiques	251
Utilisation de l’adaptateur DIGITAL MEDIA PORT	252
Attribution de noms à des entrées	256
Passage entre son numérique et analogique (INPUT MODE)	257
Écoute du son/visionnage d’images d’autres entrées	258
Changement des informations sur l’affichage	261
Utilisation de la minuterie d’arrêt	266
Enregistrement à l’aide de l’ampli-tuner	267
Écoute du son dans une autre zone (opération ZONE 2/ ZONE 3)	268
Utilisation d’un raccordement bi- amplificateur	273
Utilisation du système de commande CONTROL S	274
Utilisation sans raccordement au téléviseur	275
Utilisation de la télécommande	286
Commande de chaque appareil à l’aide de la télécommande	286
Programmation de la télécommande	288
Exécution automatique d’une séquence de plusieurs commandes (Exécution de macro-commandes)	291
Mémorisation de codes de télécommande n’ayant pas été préprogrammés dans la télécommande	293
Effacement de tout le contenu de la mémoire de la télécommande	295
Informations complémentaires	296
Glossaire	296
Précautions	299
Guide de dépannage	300
Spécifications	305

Match case Limit results 1 per page

142

are output from the VIDEO jack. Input

480i component video signals.

• When component input signals other than

480p are output, use the COMPONENT

VIDEO OUT jack and set “Resolution” to

“DIRECT.”

Images of the source with HDMI

connection is not output to the TV.

• Make sure that cables are correctly and

securely connected to components.

• Depending on the playback component,

component may need to be set up. Refer to

the operating instructions supplied with

the each component.

• Be sure to use a connecting cable for the

HDMI jack corresponding to high speed

(an HDMI version1.3a, category 2 cable)

when you view images or listen to sound

during a DeepColor transmission.

Recording cannot be carried out.

• Check that the components are connected

correctly (page 27).

•

Select the source component using INPUT

SELECTOR (page 53).

The GUI does not appear on the TV

screen.

• Press SHIFT, then press MENU to show

“GUI MODE” on the display.

• Check the TV is connected correctly.

Tuner

The FM reception is poor.

• Use a 75-ohm coaxial cable (not supplied)

to connect the receiver to an outdoor FM

antenna (aerial) as shown below. If you

connect the receiver to an outdoor antenna

(aerial), ground it against lightning. To

prevent a gas explosion, do not connect the

ground (earth) wire to a gas pipe.

Radio stations cannot be tuned in.

• Check that the antennas (aerials) are

connected securely. Adjust the antennas

(aerials) and connect an external antenna

(aerial), if necessary.

• Keep the satellite radio antenna, away

from the speaker cords and the power cord

to avoid picking up noise.

• The signal strength of the stations is too

weak (when tuning in with automatic

tuning). Use direct tuning.

• Make sure you set the tuning interval

correctly (when tuning in AM stations

with direct tuning).

• No stations have been preset or the preset

stations have been cleared (when tuning by

scanning preset stations). Preset the

stations (page 84).

• Press DISPLAY so that the frequency

appears on the display.

The system cannot receive satellite

channels at all.

•

The receiving condition is not good. Move

the antenna to the place where the

condition is good.

• Check that you subscribed to the desired

satellite radio service (see page 85).

Remote control

The remote does not function.

• Point the remote at the remote sensor on

the receiver.

Receiver

To ground

Ground (earth)

wire (not supplied)

Outdoor FM antenna (aerial)