Sony XNV-L77BT Operating Instructions - Page 73

Overcurrent Caution on USB, Local Seek +/Local Seek

Get Sony XNV-L77BT PDF manuals and user guides View all Sony XNV-L77BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Hubs not supported. USB hubs are not supported on this unit. Local Seek +/Local Seek - The local seek mode is on during automatic tuning. No device found. No device is in the list of registered Bluetooth device. t Perform pairing with a Bluetooth device (page 37). No playable data. The disc does not contain playable data. No SensMe™ data on device. The connected USB device does not contain data for the SensMe™ function, or the data has been moved to an improper location on the USB device. Offset There may be an internal malfunction. t Check the connection. If the error indication remains on the display, consult your nearest Sony dealer. Output connection failure. (Displays until any button is pressed.) The connection of speakers/amplifiers is incorrect. t See the supplied "Installation/Connections" guide to check the connection. Overcurrent Caution on USB The USB device is overloaded. t Disconnect the USB device, then change the source by pressing (SOURCE/OFF). t Indicates that the USB device is out of order, or an unsupported device is connected. Playback prohibited by region code. The DVD's region code differs from the unit's region code. Please push reset. This unit or USB device cannot be operated due to a problem. t Press the reset button (page 17). Please reset Navi. Operation is not possible due to an error of the navigation module. t Reset the navigation module. When resetting the navigation module, be sure to press and hold its reset button for more than 10 seconds; otherwise, the navigation module will not reset. SensMe™ data Reading... The unit is reading all data for the SensMe™ function in the connected USB device. t Wait until reading is complete. Depending on the amount of data, etc., it may take time. The connected USB device is not supported. For details on the compatibility of your USB device, visit the support site. The SensMe™ data is corrupted. The data for the SensMe™ function has a problem, such as altered file name, information, etc. USB device is not connected. USB is selected as source without a USB device connected. A USB device or a USB cable has been disconnected during playback. t Be sure to connect a USB device and USB cable. USB Reading... The unit is reading all file/album (folder) information in the connected USB device. t Wait until reading is complete and playback starts automatically. Depending on the structure, it may take time. Waiting for Navi connection. The navigation module is not connected or recognized. t Connect the navigation module to the car dock and wait for a moment. t Disconnect the navigation module from the car dock, and connect it again. If the problem persists, press and hold its reset button for more than 10 seconds. " " or " " During reverse or fast-forward, you have reached the beginning or the end of the disc and you cannot go any further. "" The character cannot be displayed with the unit. If these solutions do not help improve the situation, consult your nearest Sony dealer. If you take the unit to be repaired because of disc playback trouble, bring the disc that was used at the time the problem began. 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
73
If these solutions do not help improve the situation,
consult your nearest Sony dealer.
If you take the unit to be repaired because of disc
playback trouble, bring the disc that was used at the
time the problem began.
Hubs not supported.
USB hubs are not supported on this unit.
Local Seek +/Local Seek –
The local seek mode is on during automatic tuning.
No device found.
No device is in the list of registered Bluetooth device.
t
Perform pairing with a Bluetooth device (page 37).
No playable data.
The disc does not contain playable data.
No SensMe™ data on device.
The connected USB device does not contain data for
the SensMe™ function, or the data has been moved to
an improper location on the USB device.
Offset
There may be an internal malfunction.
t
Check the connection. If the error indication
remains on the display, consult your nearest Sony
dealer.
Output connection failure.
(Displays until any button is pressed.)
The connection of speakers/amplifiers is incorrect.
t
See the supplied “Installation/Connections” guide
to check the connection.
Overcurrent Caution on USB
The USB device is overloaded.
t
Disconnect the USB device, then change the source
by pressing
(SOURCE/OFF)
.
t
Indicates that the USB device is out of order, or an
unsupported device is connected.
Playback prohibited by region code.
The DVD’s region code differs from the unit’s region
code.
Please push reset.
This unit or USB device cannot be operated due to a
problem.
t
Press the reset button (page 17).
Please reset Navi.
Operation is not possible due to an error of the
navigation module.
t
Reset the navigation module. When resetting the
navigation module, be sure to press and hold its
reset button for more than 10 seconds; otherwise,
the navigation module will not reset.
SensMe™ data Reading...
The unit is reading all data for the SensMe™ function
in the connected USB device.
t
Wait until reading is complete. Depending on the
amount of data, etc., it may take time.
The connected USB device is not supported.
For details on the compatibility of your USB device,
visit the support site.
The SensMe™ data is corrupted.
The data for the SensMe™ function has a problem,
such as altered file name, information, etc.
USB device is not connected.
USB is selected as source without a USB device
connected. A USB device or a USB cable has been
disconnected during playback.
t
Be sure to connect a USB device and USB cable.
USB Reading...
The unit is reading all file/album (folder) information
in the connected USB device.
t
Wait until reading is complete and playback starts
automatically. Depending on the structure, it may
take time.
Waiting for Navi connection.
The navigation module is not connected or recognized.
t
Connect the navigation module to the car dock and
wait for a moment.
t
Disconnect the navigation module from the car
dock, and connect it again. If the problem persists,
press and hold its reset button for more than 10
seconds.
“
” or “
”
During reverse or fast-forward, you have reached the
beginning or the end of the disc and you cannot go any
further.
“
”
The character cannot be displayed with the unit.