TEAC TN-200 Owners Manual - Page 10
Troubleshooting, Specifications, Included accessories - belt drive
View all TEAC TN-200 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
Troubleshooting If you experience a problem with this unit, please check the following items before requesting service. Something other than this unit could also be the cause of the problem. Please also check that the connected devices are also being used properly. If it still does not operate correctly, contact the retailer where you purchased the unit. No power. ee Confirm that the AC adapter is plugged into an out- let. Then, press the STANDBY/ON button to turn the unit on (page 6). There is no sound. ee When connecting this unit's analog audio output jacks to the audio input jacks of an amplifier or other equipment, set the PHONO EQ (audio output setting) switch to ON (page 6). The pitch is wrong. ee Set the rotation speed (RPM) to match the record (page 8). The sound is skipping. ee Vibrations will cause skipping. Place this unit in a stable location. ee If the record is dirty, wipe it clean. ee Do not use scratched records. ee Balance the tone arm and readjust the stylus pres- sure (page 5). If the stylus pressure is lower than the value designated by the cartridge, skipping is more likely to occur. Playback is not possible; there is noise. ee Confirm that the stylus cover (made of white plas- tic) has been removed. ee Clean the stylus (page 5). ee If the stylus is worn-out, replace it (page 5). ee Place the unit as far away as possible from TVs, microwave ovens and other devices that emit electromagnetic waves. Specifications Turntable Drive system Belt drive Motor DC motor Rotation speed 33 1/3 rpm, 45 rpm Rotation speed variation 2% Wow and flutter 0.2% SN ratio 67 dB or higher (A-weighted, 20 kHz LPF) Turntable Aluminum die-cast 30cm (12") diameter Tone arm Arm type Static-balanced straight-pipe tone arm Effective arm length 223 mm Stylus pressure variation range 0-5 g Acceptable cartridge weight 3.5-6.5 g Cartridge Type MM Output voltage 2.4 mV ±3 dB Stylus pressure 3.0 ±0.5 g Cartridge weight 4.3 ±0.4 g Included headshell weight 10 g (including screws, nuts and wires) Output voltage PHONO EQ THRU 2.4 mV ±3 dB PHONO EQ ON 149 mV (−16.5 dBV) Output jacks RCA USB port USB port that can receive power from computer USB buses (Full Speed USB connector type B USB bus power support 5 V, 500 mA ooUse a commercially-available USB cable connect the unit to a computer to receive power from it. Sampling frequency 8 kHz, 11.025 kHz, 16 kHz, 22.05 kHz, 32 kHz, 44.1 kHz, 48 kHz Quantization bit depth 16-bit General AC adapter power Input AC 100 V-AC 240 V, 50-60 Hz Output 12 V, 500 mA Power consumption Standby 0.5 W or less On (START 1.5 W or less Weight 4.9 kg (10 7/8 lb) Operating temperature range 5°C to 35°C Dimensions (W × H × D) (including protrusions) 420 × 117 × 356 mm (16 5/8" × 4 5/8" × 14 1/8") ooPerformance data is specified at 20°C. Included accessories Rubber mat × 1 45 RPM adapter × 1 Counterweight × 1 Headshell × 1 CR2861 MM cartridge preinstalled Turntable × 1 Turntable cover × 1 Hinges × 2 Audio cable × 1 AC adapter × 1: Model for USA/Canada: GPE053A-120050-1 Model for Europe: GPE053A-120050-Z Owner's manual (this document) × 1 Warranty card × 1 (for customers in the USA and Canada only) ooSpecifications and appearance are subject to change without notice. ooWeight and dimensions are approximate. ooIllustrations in this owner's manual might differ slightly from production models. 10