TEAC TN-4D Owners Manual - Page 14

Before use continued, Preparing the record player - turntable

Get TEAC TN-4D PDF manuals and user guides View all TEAC TN-4D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Before use (continued) Precautions for use oo Do not place anything on the dust cover. Objects on the cover might cause noise due to vibrations or fall off, especially during playback. oo Avoid placing the unit in direct sunlight, close to a source of heat or in other similar conditions. Do not place the unit on top of an amplifier or other equipment that might generate heat that exceeds the operating temperature range of this unit. Doing so could cause discoloration, deformation or malfunction. oo As the unit could become warm during operation, always leave sufficient space around it for ventilation. When installing this unit, leave a little space (at least 20 cm (8")) between it and other devices and walls to allow good heat dissipation. When placing it in a rack, for example, leave at least 35 cm (13 3/4") open above it and 10 cm (4") open behind it. Failure to provide these gaps could cause heat to build up inside and result in fire. oo DO NOT MOVE THE UNIT DURING PLAYBACK. During playback, the record rotates. Do not lift or move the unit during playback. Doing so may damage the record, the stylus, the cartridge or the unit. oo Always remove the record before relocating or moving this unit. Moving the unit with a record on the turntable (platter) could damage the record, the stylus and the cartridge or could cause a malfunction. oo The voltage supplied to the unit should match the voltage as printed on the rear panel. If you are in any doubt regarding this matter, consult an electrician. Maintenance If the surface of the unit gets dirty, wipe it with a soft cloth or use diluted mild liquid soap. Allow the surface of the unit to dry completely before using. oo Do not use chemical cleaning cloths, thinner or similar sub- stances as they could damage the surface of the unit. VV CAUTION For safety, disconnect the power cord from the socket before cleaning. Using the TEAC Global Site You can download updates for this unit from the TEAC Global Site: http://teac-global.com/ In the TEAC Downloads section, click the desired language to open the Downloads website page for that language. NG NG NG Preparing the record player Keep the unit in standby while setting it up ( F on page 16). 1 Cushions are attached to the tone arm for use during transportation. Remove them in the directions of the arrows. 4 Place the felt mat on the turntable (platter). Place the included felt mat on the turntable (platter) before using it. AN 0 3 AN 0 3 Cushion for transportation TI-SKATI TI-SKATI Cushion for transportation 2 Place the unit on a flat surface. Place it on a flat surface so that the record can be accurately traced. 3 Install the turntable (platter). Align the turntable (platter) with the center shaft and install it. oo Place the large side of the hole down. 5 Install the counterweight. Place the counterweight over the end of the tone arm, and press it gently as you turn it right to attach it. oo When the counterweight can be moved toward the bearing, installation is complete. Counterweight Center shaft Turntable (platter) TI-SKATI Bearing AN 0 3 6 Install the headshell. Insert the headshell on the end of the tone arm and turn the nut to secure it in place. Nut Headshell 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
14
Before use (continued)
Keep the unit in standby while setting it up (
F
on page 16).
1
Cushions are attached to the tone arm
for use during transportation. Remove
them in the directions of the arrows.
3
0
A
N
T
I
–
S
K
A
T
I
N
G
3
0
Cushion for
transportation
Cushion for
transportation
2
Place the unit on a flat surface.
Place it on a flat surface so that the record can be accurately
traced.
3
Install the turntable (platter).
Align the turntable (platter) with the center shaft and
install it.
o
Place the large side of the hole down.
Center shaft
Turntable (platter)
4
Place the felt mat on the turntable
(platter).
Place the included felt mat on the turntable (platter)
before using it.
5
Install the counterweight.
Place the counterweight over the end of the tone arm,
and press it gently as you turn it right to attach it.
o
When the counterweight can be moved toward the
bearing, installation is complete.
A
N
T
I
–
S
K
A
T
I
N
G
3
0
Counterweight
Bearing
6
Install the headshell.
Insert the headshell on the end of the tone arm and turn
the nut to secure it in place.
Headshell
Nut
Preparing the record player
Precautions for use
o
Do not place anything on the dust cover. Objects on the
cover might cause noise due to vibrations or fall off, espe-
cially during playback.
o
Avoid placing the unit in direct sunlight, close to a source
of heat or in other similar conditions. Do not place the unit
on top of an amplifier or other equipment that might gen-
erate heat that exceeds the operating temperature range of
this unit. Doing so could cause discoloration, deformation
or malfunction.
o
As the unit could become warm during operation, always
leave sufficient space around it for ventilation. When
installing this unit, leave a little space (at least 20  cm (8
"
))
between it and other devices and walls to allow good heat
dissipation.
When placing it in a rack, for example, leave at least 35 cm
(13  3/4
"
) open above it and 10  cm (4
"
) open behind it.
Failure to provide these gaps could cause heat to build up
inside and result in fire.
o
DO NOT MOVE THE UNIT DURING PLAYBACK. During play-
back, the record rotates. Do not lift or move the unit during
playback. Doing so may damage the record, the stylus, the
cartridge or the unit.
o
Always remove the record before relocating or moving this
unit. Moving the unit with a record on the turntable (plat-
ter) could damage the record, the stylus and the cartridge
or could cause a malfunction.
o
The voltage supplied to the unit should match the voltage
as printed on the rear panel. If you are in any doubt regard-
ing this matter, consult an electrician.
Maintenance
If the surface of the unit gets dirty, wipe it with a soft cloth or
use diluted mild liquid soap. Allow the surface of the unit to dry
completely before using.
o
Do not use chemical cleaning cloths, thinner or similar sub-
stances as they could damage the surface of the unit.
V
CAUTION
For safety, disconnect the power cord from the socket before
cleaning.
Using the TEAC Global Site
You can download updates for this unit from the TEAC Global
Site:
http://teac-global.com/
In the TEAC Downloads section, click the desired language to
open the Downloads website page for that language.