TP-Link AC1900 Archer C9 V2 User Guide

TP-Link AC1900 Manual

Get TP-Link AC1900 PDF manuals and user guides View all TP-Link AC1900 manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link AC1900 manual content summary:

  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 1
    Archer C9 AC1900 Wireless Dual Band Gigabit Router REV2.0.0 1910011382
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 2
    COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 3
    installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 4
    2012 MHz Italy None If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 5
    used outside own premises General authorization required for network and service supply (not for spectrum) Country Bulgaria Restriction Not implemented of DFS mechanism described in ETSI standard EN 301 893 V1.3.1 and subsequent versions General authorization required if used outside own
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 6
    Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 7
    power source.  Don't disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.  Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 8
    Product Description: AC1900 Wireless Dual Band Gigabit Router Model No.: Archer C9 Trademark: TP-LINK We declare under in conformity with the following standards or other normative documents EN 300 328 V1.8.1 EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1 EN 55022: 2010 + AC: 2011 EN 55024: 2010 EN
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 9
    Layout ...4 1.4.1 The Front Panel 4 1.4.2 The Rear Panel 5 Chapter 2. Connecting the router 7 2.1 System Requirements 7 2.2 Installation Environment Requirements 7 2.3 Connecting the router 7 Chapter 3. Quick Setup 9 Chapter 4. Basic 15 4.1 Network Map ...15 4.2 Internet ...15 4.3 Wireless
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 10
    5.10 Forwarding ...67 5.10.1 Virtual Servers 67 5.10.2 Port Triggering 69 5.10.3 DMZ...71 5.10.4 UPnP ...72 5.11 Security ...73 5.11.1 Basic Security 73 5.11.2 Advanced Security 74 5.11.3 Local Management 76 5.11.4 Remote Management 77 5.12 Parental Control ...78 5.13 Access
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 11
    DDNS 99 5.18 IPv6 Support ...100 5.18.1 IPv6 Status 101 5.18.2 IPv6 Setup 102 5.19 System Tools ...110 5.19.1 Time Settings 110 5.19.2 Diagnostic 112 5.19.3 Firmware Upgrade 114 5.19.4 Factory Defaults 115 5.19.5 Backup & Restore 115 5.19.6 Reboot ...116 5.19.7 Password...117 5.19.8 System
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 12
    in your package:  Archer C9 AC1900 Wireless Dual Band Gigabit Router  DC Power Adapter for Archer C9 AC1900 Wireless Dual Band Gigabit Router  Quick Installation Guide  Resource CD for Archer C9 AC1900 Wireless Dual Band Gigabit Router, including:  This Guide  Other Helpful Information  Note
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 13
    Setup Wizard is supported and detailed instructions are provided step by step in this user guide. Before installing the router, please look through this guide to know all the router's functions. 1.2 Conventions The router or Archer C9 mentioned in this guide stands for Archer C9 AC1900 Wireless
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 14
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 1.3 Main Features  Complies with IEEE 802.11ac.  One 10/100/1000M Auto-Negotiation RJ45 Internet port, four 10/100/1000M Auto-Negotiation RJ45 Ethernet ports, supporting Auto MDI/MDIX.  Provides a USB 3.0 port and a USB 2.0 port supporting file
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 15
    1.4 Panel Layout 1.4.1 The Front Panel Archer C9 AC1900 Wireless Dual Band Gigabit Router The router's LEDs are located on the front panel (View from left to right). Name (Power) (2.4G Wireless) (5G Wireless) (Ethernet) (Internet) (WPS) (USB 1) Status Flashing On
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 16
    or a USB 2.0 printer.  Reset/WPS: Pressing this button for less than 5 seconds enables the WPS function. If your client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can press this button to quickly establish a connection between the router and client devices and
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 17
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Pressing this button for more than 5 seconds enables the Reset function. With the router powered on, press and hold the Reset/WPS button for approximately 8 seconds. And then release the button and wait the router to reboot to its factory default
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 18
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Chapter 2. Connecting the router 2.1 System Requirements  Broadband Internet Access Service (DSL/Cable/Ethernet)  One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the router Internet port on your router with an Ethernet cable.
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 19
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 2-1 Hardware Installation Figure 2-2 USB Installation  Note: If you want to use the router to share files or printer, plug the USB storage device to the USB port or connect the printer to the router with a matching cable. - 8 -
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 20
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Chapter 3. Quick Setup 1. Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC. If you need instructions as to how to do this, please refer to Appendix B: Configuring the PC. 2. Open a web-browser (such as Microsoft
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 21
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 4. Then WAN Connection Type page will appear as shown below. Select your connection type if you know what it is or click Auto Detect button; then follow the instructions to continue.  Note: 1) It's likely that you will skip Step 3 and jump to Step
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 22
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 3-6 WAN Connection Type  IP Address - Enter the IP address into this field.  Subnet Mask - Enter the subnet mask into this field. It is usually 255.255.255.0.  Default Password - Enter the password provided by your ISP. This field is case
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 23
    L2TP Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 3-8 WAN Connection Type  VPN Server IP/ Domain Name - Enter the server IP address/name provided by your ISP.  Username - Enter the username provided by your ISP. This field is case-sensitive.  Password - Enter the Password provided
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 24
    PPTP Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 3-9 WAN Connection Type  VPN Server IP/Domain Name - Enter the server IP address/name provided by your ISP.  Username - Enter the username provided by your ISP. This field is case-sensitive.  Password - Enter the Password provided
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 25
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Wireless 2.4GHz/5GHz - Displays whether the wireless function is enabled or not.  Network Name (SSID) - Also called the SSID (Service Set Identification). Enter a value of up to 32 characters. The same name must be assigned to all wireless
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 26
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Chapter 4. Basic 4.1 Network Map Network Map provides a router-centered dashboard Click to view or change the wireless settings for your router.  Printer - Click to view the information of the printer connected to your network.  USB Disk - Click
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 27
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 4-2 Internet 1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the router will automatically get IP parameters from your ISP. You can see the page as shown below. Figure 4-3 Dynamic IP  IP Address - Assigned
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 28
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Primary/Secondary DNS - If your ISP gives the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0.  Default Gateway - Enter the gateway IP address in dotted-decimal notation provided by your ISP.  Primary/
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 29
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 4-5 PPPoE  User Name/Password - Enter the User Name and Password provided by your L2TP  VPN Server IP/Domain Name - Enter the IP address or domain name of your VPN server.  User Name/Password - Enter the User Name and Password provided by
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 30
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5. If your ISP provides PPTP connection, please select PPTP/Russia PPTP option. And you should enter the following parameters (Figure 5-8). Figure 4-7 PPTP/Russia PPTP  VPN Server IP/Domain Name - Enter the IP address or domain name of your VPN
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 31
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 4.3 Wireless Choosing menu "Basic→Wireless", you can configure the wireless network will be hidden from the Wi-Fi network.  Password - Create a password for your wireless network. The password must have a minimum of 8 characters in length. Click the
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 32
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 4-9 File Sharing  Device Setting - Click the Scan button to display the information of the USB storage device connected to the router. Click the Safely Remove button to remove the USB storage device safely from the router. Select the Active
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 33
    Archer C9 AC1900 Wireless Dual Band Gigabit Router ii. Enter ftp://192.168.0.1:21 in the dialog box and click the OK button. 3) FTP (Remote): This method is disabled by default. If you select this check box, remote users can access the USB drive through FTP over the Internet. This feature supports
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 34
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Allow Guest Network Access - If this checkbox is selected, guests are allowed to access the sharing file.  Enable Authentication - If this checkbox is selected, then the file sharing is need authentication.  Enable Write Access - If this
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 35
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 4-12 Guest Network  Allow Guests To See Each Other - If ON is selected, anyone who connects to the guest network can access each other.  Allow Guests To Access Password - Create a password for the guest network. The password must have a minimum of
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 36
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Chapter 5. Advanced 5.1 Status Choose menu "Advanced→Status", you can see the current status information about the router. Figure 5-1 Status - 25 -
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 37
    5.2 Network Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-2 the Network menu There are three the WAN on the screen below. 1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the router will automatically get IP parameters from your ISP. You can see the page
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 38
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default the router.  Get IP with Unicast DHCP - A few ISPs' DHCP servers do not support the broadcast
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 39
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default WAN - PPPoE  User Name/Password - Enter the User Name and Password provided by your ISP. These
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 40
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Static IP - You can check this radio button to use Static IP as the secondary connection to connect to the local area network provided by ISP.  Connect on Demand - In this mode, the Internet connection can be terminated automatically after a
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 41
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-6 PPPoE Advanced Settings  MTU Size - The default MTU size is "1480" bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP.  Service Name/AC Name - The service name and AC (
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 42
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-7 WAN - L2TP/Russia L2TP  VPN Server IP/Domain Name - Enter the IP address or domain name of the VPN server provided by your ISP.  User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 43
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Connect Automatically - Connect automatically after the router is disconnected. To use this option, check the radio button.  Connect Manually - You can configure the router to make it connect or disconnect manually. After a specified period of
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 44
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  VPN Server IP/Domain Name - Enter the IP address or domain name of the VPN server provided by your ISP.  User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.  Dynamic IP/ Static IP - Select
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 45
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Static IP - Connections which use static IP address assignment. The router cannot detect PPTP/L2TP connections with your ISP. If your ISP uses one of these protocols, then you must configure your connection manually. 5.2.2 MAC Clone Choose
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 46
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-10 LAN  MAC Address - The physical address of the router, as seen from the LAN. The value can't be changed.  IP Address - Enter the IP address of your router or reset it in dotted-decimal notation (factory default: 192.168.0.1).  Subnet
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 47
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5.4 Wireless 2.4GHz Figure 5-12 Wireless menu There - The wireless network name (SSID) that the router uses. You can create a new one with up to 32 characters. The default SSID is set to be TP-LINK_XXXX. This value is case-sensitive. For example
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 48
    operating frequency will be used. The default channel is set to Auto, so the router will choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.  Enable SSID Broadcast - When wireless clients
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 49
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  MAC Address (to be bridged) - The MAC address (BSSID) of the AP your router is going to connect to as a client. You can also use the Survey function to select the MAC address (BSSID) to join.  Survey - Click this
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 50
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Use this method if your client device has a WPS button. Step 1: Press the WPS/Reset button on the back panel of the router. Step 2: Press and hold the WPS button of the client device. The WPS LED flashes for two minutes during the Wi-Fi Protected
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 51
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-17 Wireless Security  Disable Security - If you do not want to use wireless security, check this radio button. But it's strongly recommended to choose one of the following modes to enable security.  WPA/WPA2-Personal - It's the WPA/WPA2
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 52
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-18 WPA/WPA2 - Personal  Wireless Password - You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. The default password is the same with the default PIN code, which is labeled on the router or can be
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 53
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update.  WEP - It is based on the IEEE 802.11 standard. If you check this radio button, you will find a notice in
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 54
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5.4.4 Wireless MAC Filtering Choose menu "Advanced→Wireless 2.4GHz→Wireless MAC Filtering", you can control the wireless access or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 55
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 3. Select Enabled or Disabled for this entry with MAC address 00-0A-EB-00-07-5F are able to access the router, but all the other wireless stations cannot access the router, you can configure the Wireless MAC Address Filtering list by following these
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 56
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5.4.5 Wireless Advanced Choose menu "Advanced→Wireless 2.4GHz→Wireless may result in poor network performance because of excessive packets. 2346 is the default setting and is recommended.  DTIM Interval - This value determines the interval
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 57
    Archer C9 AC1900 Wireless Dual Band Gigabit Router broadcast and multicast messages. When the router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 58
    Archer C9 AC1900 Wireless Dual Band Gigabit Router If the numbers of connected wireless stations go beyond one page, Settings (5GHz)  Wireless Network Name - The wireless network name (SSID) that the router uses. You can create a new one with up to 32 characters. The default SSID is set to be - 47 -
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 59
    operating frequency will be used. The default channel is set to Auto, so the router will choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.  Enable SSID Broadcast - When wireless clients
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 60
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  MAC Address (to be bridged) - The MAC address (BSSID) of the AP your router is going to connect to as a client. You can also use the Survey function to select the MAC address (BSSID) to join.  Survey - Click this
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 61
    Archer C9 AC1900 Wireless Dual Band Gigabit Router If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and router using either Push Button Configuration (PBC) method or PIN method.  Note: To build a successful connection by
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 62
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5.5.3 Wireless Security Choose menu "Advanced→Wireless 5GHz→Wireless Security", you can configure the security settings of your wireless network. There are five wireless security modes supported by the router: WPA-Personal, WPA2-Personal, WPA-
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 63
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Note: If you check the WPA/WPA2-Personal radio button and choose TKIP encryption, you will find a notice in red as shown in Figure 5-31. Figure 5-31 WPA/WPA2 - Personal  Wireless Password - You can enter ASCII characters between 8 and 63
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 64
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Radius Server IP - Enter the IP address of the Radius server.  Radius Port - Enter the port number of the Radius server.  Radius Password - Enter the password for the Radius server.  Group Key Update Period - Specify the group key update
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 65
    Archer C9 AC1900 Wireless Dual Band Gigabit Router →MAC Filtering", you can control the wireless access by configuring the Wireless MAC Filtering function, To filter wireless users by MAC Address, click Enable. The default setting is Disabled.  MAC Address - The wireless station instructions: - 54 -
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 66
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 1. Enter the appropriate MAC Address into the with MAC address 00-0A-EB-00-07-5F are able to access the router, but all the other wireless stations cannot access the router, you can configure the Wireless MAC Address Filtering list by following these
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 67
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5.5.5 Wireless Advanced Choose menu "Advanced→Wireless→Wireless Advanced", you can configure the advanced settings of your wireless network. Figure 5-36 Wireless Advanced  Transmit Power - Here you can specify the transmit power of router. You
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 68
    Archer C9 AC1900 Wireless Dual Band Gigabit Router messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default any of the values on this page. To update this page and to show the current connected wireless
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 69
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Note: This page will be refreshed automatically every 5 seconds. 5.6 Guest Network Choose menu "Advanced→Guest Network", you can configure the Guest Network Wireless Settings on
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 70
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Access And Bandwidth Control  Allow Guests to See Each Other - If this checkbox is selected, anyone who connects to the guest network can communicate with each other.  Allow Guests To Access My Local Network - If this checkbox is selected,
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 71
    5.7 DHCP Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-39 The DHCP menu There are three must configure the computer manually.  Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address.  End
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 72
    Archer C9 AC1900 Wireless Dual Band Gigabit Router the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes.  Default Gateway - (Optional.) It is suggested to input the IP address of the Ethernet port update this
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 73
    Archer C9 AC1900 Wireless Dual Band Gigabit Router accesses the DHCP server. Reserved IP addresses should be to reserve an IP address.  Reserved IP Address - The IP address reserved for the PC by the router.  Status - The status of this entry, either Enabled or Disabled. To Reserve an IP address:
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 74
    Archer C9 AC1900 Wireless Dual Band Gigabit Router scan the USB drive connected to the router.  Volume - The volume name of the USB drive the users have access to. Volume 1-8 is mapping to the USB storage device that is connected to USB port. This takes the drive offline. 5.8.2 File Sharing
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 75
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-46 File Sharing  Sharing Account  Use Login Account - Select this radio button, and the sharing account is the same with the login account.  Use Following Account - Select this radio button, then you have to specify the new username and
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 76
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 2) FTP: This method is disabled by default. If you select this check box and click the Save button, the LAN users can access the USB drive through FTP. To access the USB drive for example from a Windows computer: i. Select Start > Run. ii. Enter ftp
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 77
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Allow Guest Network Access - If this checkbox is selected, guests are allowed to access the sharing file.  Enable Authentication - If this checkbox is selected, then the file sharing is need authentication.  Enable Write Access - If this
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 78
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5.10 Forwarding Figure 5-49 NAT Boost Figure 5-50 The Forwarding menu There are four submenus under the Forwarding menu: Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the corresponding
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 79
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Service Port - The numbers of External Service Ports. You can enter a service port or a range of service ports (the format is XXX - YYY; XXX is the Start port and YYY is the End port).  Internal Port - The Internal Service Port number of the PC
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 80
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Note: It is possible that you have a computer or server that has more than one type of available service. If so, select another service 10.2 Port Triggering Choose menu "Advanced→Forwarding→Port Triggering", you can view and add port triggering in
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 81
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 3. Select the protocol used for Trigger Port from the Trigger Protocol drop-down list, either TCP, UDP, or All. 4. Select the protocol used for Incoming Ports from the Incoming Protocol drop-down list, either TCP or UDP, or All. 5. Select Enabled in
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 82
    allows one local host to be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing. The router forwards packets of all services to the DMZ host. Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 83
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5.10.4 UPnP Choose menu "Advanced→Forwarding→UPnP", and then you can view the information about UPnP in the screen shown in Figure 5-56. The Universal Plug and Play (UPnP) feature allows the devices, such as Internet computers, to access the local
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 84
    5.11 Security Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-57 The Security menu There are four submenus under passing through the session conforms to the protocol. SPI Firewall is enabled by factory default. If you want all the computers on the LAN exposed to the outside world, you can disable
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 85
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  VPN - VPN Passthrough must be enabled if you want to allow VPN tunnels using VPN protocols to pass through the router.  PPTP Passthrough - Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point Protocol (PPP) to be tunneled through an
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 86
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-59 Advanced Security  Packets Statistics Interval (5~60) - The default value is SYN Flood, UDP Flood and ICMP-Flood.  DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 87
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Enable TCP-SYN-FLOOD Attack Filtering - Enable or Disable the TCP-SYN-FLOOD Attack Filtering.  TCP-SYN-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current TCP-SYN-FLOOD Packets numbers is
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 88
    the port number used is 8080, please enter http://202.96.12.8:8080 in your browser. Later, you may be asked for the router's password. After successfully entering the username and password, you will be able to access the router's web-based utility. 2. Be sure to change the router's default password
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 89
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5.12 Parental Control Choose menu "Advanced→ Schedule - The time period allowed for the PC controlled to access the Internet. For detailed information, please go to "Advanced→Access Control→Schedule".  Status - Check to enable the corresponding
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 90
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-63 Add or Modify Parental Control Entry 2. Enter the MAC address of example: If you desire that the child PC with MAC address 00-11-22-33-44-AA can access www.google.com on Saturday only, while the parent PC with MAC address 00-11-22-33-44-
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 91
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 1. Click "Parental Control" menu on the left to enter the Parental Control Settings page. Check Enable and enter the MAC address 00-11-22-33-44-BB in the MAC Address of Parental PC field. 2. Click "Advanced→Access Control→Schedule" on the left to
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 92
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5.13.1 Rule Choose menu "Advanced→Access Control→Rule", and then you can view and set Access Control rules in the screen as shown in Figure 5-65. Figure 5-65 Access Control Rule Management  Enable Internet Access Setup Wizard - Click the Setup
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 93
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Move - You can change the entry's order as shown in Figure 5-66. Figure 5-66 Quick Setup - Create a Host Entry  Host Description - In this field, create a unique description for the host (e.g. Host_1).  Mode - Here are two options, IP Address and
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 94
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-67 Quick Setup - Create an Access Target Entry  Target Description - In this field, create a description for the target. Note that this description should be unique (e.g. Target_1).  Mode - Here are two options, IP Address and Domain Name
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 95
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-68 Quick Setup or deselect the checkbox and specify the Start Time and Stop Time manually.  Start Time - Enter the start time in HHMM format ( Figure 5-69. Figure 5-69 Quick Setup - Create an Internet Access Control Entry  Rule Name - In
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 96
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Target - In this filed, select a target from the menu Access Control on the left. Select Enable Internet Access Control and choose "Allow the packets specified by any enabled access control policy to pass through the router". 2. Click Setup Wizard
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 97
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-71. The host list is necessary for the Access Control Rule. Figure 5-71 Host Settings  Host Description the steps below. 1. Click the Add New... button. 2. In the Mode field, select IP Address or MAC Address. 1) If you select IP Address
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 98
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-72 Add or Modify a Host Entry 2) If you Add New... button in Figure 5-71 to enter the Add or Modify a Host Entry page. 2. In Mode field, select MAC Address from the drop-down list. 3. In Host Description field, create a unique description
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 99
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5.13.3 Target Choose menu "Advanced→Access Control→Target", and then you can view and set a Target list in the screen as shown in Figure 5-74. The target list is necessary for the Access Control Rule. Figure 5-74 Target Settings  Target Description
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 100
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-76 Add or Modify an Access Target Entry 1) In Target Description field, AA in the LAN to access www.google.com only, you should first follow the settings below: 1. Click Add New... button in Figure 5-74. 2. In Mode field, select Domain Name
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 101
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-77 Schedule Settings  Schedule Description - Displays the description of the schedule and this description is unique.  Day - Displays the day(s) in a week.  Time - Displays
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 102
    Archer C9 AC1900 Wireless Dual Band Gigabit Router For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA to access www.google.com only from 18:00 to 20:00 on Saturday and Sunday, you should first follow the settings below: 1. Click Add New...
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 103
    Archer C9 AC1900 Wireless Dual Band Gigabit Router To add static routing entries: 1. Click Add New... shown and which portion is the host portion.  Default Gateway - This is the IP Address of the gateway device that allows for contact between the router and the network or host. 3. Select Enabled or
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 104
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-82 System Routing Table  Destination Network Gateway - This is the IP address of the gateway device that allows for contact between the router and the network or host.  Interface - This interface tells you either the Destination IP Address
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 105
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-84 Bandwidth Control Settings  Enable Bandwidth bandwidth through the Internet port, the default is 0.  Ingress bandwidth - This field displays the max and mix download bandwidth through the Internet port, the default is 0.  Enable
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 106
    Archer C9 AC1900 Wireless Dual Band Gigabit Router To add/modify a Bandwidth Control rule, follow the steps below. 1. Click Add New... shown in Figure 5-85, you will see a new screen shown in Figure 5-
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 107
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-88 Binding Setting  MAC Address - The MAC address of the controlled computer in the LAN.  IP Address - The assigned IP address of the controlled
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 108
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 1. Click the Find button in Figure 5-88. 2. Enter the MAC Address or IP Address. 3. Click the Find button in Figure 5-90. Figure 5-90 Find IP &
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 109
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Note: An item could not be instructions: 1. Enter the Domain Name your dynamic DNS service provider gave. 2. Enter the User Name for your DDNS account. 3. Enter the Password for your DDNS account. 4. Click the Login button to login the DDNS service
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 110
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Connection Status -The status of the DDNS service connection is displayed here. Click Logout to log out of the DDNS service.  Note: If you want to login again with another account after a successful login, please click the Logout button, then input
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 111
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-94 No-ip.com DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the User Name for your DDNS account. 2. Enter the Password for your DDNS account. 3. Enter the Domain Name you received from dynamic DNS service provider. 4.
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 112
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-96 IPv6 Status The IPv6 Status page displays the router's current IPv6 status and configuration. All information is read-only.  WAN  Connection Type - The IPv6 connection way for WAN  IPv6 Address - The WAN IPv6 address  IPv6 Default
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 113
    5.18.2 IPv6 Setup Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-97 Enable/Disable IPv6  Enable IPv6 - Tick the checkbox to enable the IPv6 function. It's enabled by default.  WAN Connection Type - Choose the correct WAN connection type based on your ISP network topology.  DHCPv6 -
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 114
    1) DHCPv6 Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-98 DHCPv6 - SLAAC Figure 5-99 DHCPv6 - DHCPv6 Server  Get non-temporary IPv6 address - Get a non-temporary IPv6 address from the ISP. - 103 -
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 115
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Get IPv6 prefix delegation - Get a temporary IPv6 address and IPv6 prefix from the ISP, the temporary IPv6 address is set to the WAN port, and the LAN port advertise IPv6 address by RADVD or DHCPs.  IPv6 Address - The IPv6 address assigned by
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 116
    2) Static IPv6 Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-100 Static IPv6 - SLAAC Figure 5-101 Static IPv6 - DHCPv6 Server  IPv6 Address - Enter the IPv6 address in dotted-decimal notation provided by your ISP.  Default Gateway - Enter the default gateway in dotted-decimal
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 117
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  MTU Size - The router with the current DHCPv6 Address. Enter the amount of time (in seconds) that the DHCPv6 address will be leased. The time range is 1~691200 seconds. The default value is 86400 seconds.  LAN IPv6 Address - Displays the LAN IPv6
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 118
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-103 PPPoEv6 - DHCPv6 Server  User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.  Get IPv6 Address Way  Get non-temporary IPv6 address - Get a non-temporary IPv6 address by DHCPv6
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 119
    Archer C9 AC1900 Wireless Dual Band Gigabit Router DHCPv6 address will be leased. The time range is 1~691200 seconds. The default value is 86400 seconds.  LAN IPv6 Address - Displays the LAN IPv6 Address. 4) Tunnel 6to4 Figure 5-104 Tunnel 6to4 - SLAAC - 108 -
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 120
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-105 Tunnel 6to4 - DHCPv6 Server  Address/Subnet Mask/Default Gateway - the IPv4 address/ subnet mask/ default or two DNS IPv6 addresses, select Use the following IPv6 DNS Servers and enter the Primary IPv6 DNS and Secondary IPv6 DNS into
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 121
    Address - Displays the LAN IPv6 Address. 5.19 System Tools Figure 5-106 The System Tools menu Choose menu "System Tools", and you can see the submenus under the main menu: Time Settings, Diagnostic, Firmware Upgrade, Factory Defaults, Backup & Restore, Reboot, Password, System Log and Statistics
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 122
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-107 Time settings  Time Zone - Select .  Daylight Saving Status - Displays the status whether the Daylight Saving is in use. To set time manually: 1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 123
    Archer C9 AC1900 Wireless Dual Band Gigabit Router To set time automatically: 1. Select your local time zone. 2. once you login to the router successfully; otherwise, these functions will not take effect. 2. The time will be lost if the router is turned off. 3. The router will automatically obtain
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 124
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-109 Diagnostic Tools  Diagnostic Tool - Check the radio button to select one diagnostic too.  Ping - This diagnostic tool troubleshoots have a name resolution problem. In this case the target (destination). The default is 20. Click Start to
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 125
    hardware version. The hardware version of the upgrade file must accord with the router's current hardware version. To upgrade the router's firmware, follow these instructions below: 1. Download a most recent firmware upgrade file from our website (www.tp-link.com). 2. Enter or select the path name
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 126
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Note: 1) New firmware versions are posted at www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 127
    .  Change the Wireless configurations.  Change the Web Management Port.  Upgrade the firmware of the router (system will reboot automatically).  Restore the router's settings to factory defaults (system will reboot automatically).  Update the configuration with the file (system will reboot
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 128
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5.19.7 Password Choose menu "Advanced→System Tools→Password", and then you can change the factory default user name and password of the router in the next screen as shown in Figure 5-115. Figure 5-115 Password It is strongly recommended that you
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 129
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-116 System Log  Auto Mail Feature - Indicates whether auto mail feature is enabled or not.  Mail - Most SMTP Server requires Authentication. It is required by most mailboxes that need User Name and Password to log in. - 118 -
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 130
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  Note: Only when you select Authentication, do you have to enter the User Name and Password in the following fields.  User Name - Your mail account name filled in the From field. The part behind @ is included.  Password - Your mail account
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 131
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure 5-118 Statistics  Current Statistics Status - Enable or Disable. The default value is to refresh automatically. Click the Refresh button to refresh immediately. Click Reset All to reset the values of all the entries to zero. Click Delete All
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 132
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Statistics Table: IP/MAC Address The IP and MAC address are displayed with related statistics. Total The total number of packets received and transmitted by the Packets router Max transmitting rate". Modify Reset Delete Reset the value of the
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 133
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Appendix A: FAQ 1. How do I configure the router to access Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the Internet port on the router. The
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 134
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 2. How do I configure the router to access Internet by Ethernet users? 1) Login to the router, click the "Network" menu on the left of your browser, and click "WAN" submenu. On the WAN page, select "Dynamic IP" for "WAN Connection Type",
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 135
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure A-5 Add or Modify a Virtual server Entry  Note: Your opposite side should call your WAN IP, which is displayed on the "Status" page. 4) How to enable DMZ Host: Log in to the router, click the "Forwarding" menu on the left of your browser,
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 136
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Figure A-7 Basic Security 4. I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the router, you must change the WEB management port number to avoid
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 137
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 3) Log in to the router, click the "Forwarding" menu on the left of your browser, and click the "Virtual Servers" submenu. On the "Virtual Servers" page, click Add New..., then on the "Add
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 138
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Appendix B: Configuring the PC In this section, we'll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter's manual if needed. 1. Install TCP/IP component
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 139
    Archer C9 AC1900 Wireless Dual Band Gigabit Router 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. 6) Select Obtain an IP address automatically and Obtain DNS server automatically, as shown in the Figure below: Figure B-3 2. Verify the
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 140
    Archer C9 AC1900 Wireless Dual Band Gigabit Router  If the result displayed is similar to Figure B-5, it means the connection between your PC and the router failed. Figure B-5 Failure result of Ping command Please check the connection following these steps: 1. Is the connection between your PC and
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 141
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Appendix C: Specifications General Standards Protocols Ports Cabling 100/1000M Auto-Negotiation Internet RJ45 port; 4 10/100/1000M Auto-Negotiation Ethernet RJ45 ports supporting Auto MDI/MDIX; 2 USB ports supporting storage/FTP/Media/Print Server;
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 142
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Appendix D: Glossary  802.11ac - IEEE 802.11ac is a wireless computer that allows data to be sent or received over existing traditional phone lines.  ISP (Internet Service Provider) - A company that provides access to the Internet. - 131 -
  • TP-Link AC1900 | Archer C9 V2 User Guide - Page 143
    Archer C9 AC1900 Wireless Dual Band Gigabit Router Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection.  SSID - A Service ESSID in the wireless Access Point and to the wireless
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Archer C9
AC1900 Wireless Dual Band Gigabit Router
REV2.0.0
1910011382