TP-Link TD-W8951NB TD-W8951NB V4 User Guide - Page 35

TD-W8951NB, Router Local IP, IP Address, IP Subnet Mask, Dynamic Route, RIP2-B, Direction, IN only

Get TP-Link TD-W8951NB PDF manuals and user guides View all TP-Link TD-W8951NB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide Figure 4-11 ¾ Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. • IP Address: Enter the Router's local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1. • IP Subnet Mask: Enter the Router's Subnet Mask, the default value is 255.255.255.0. • Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version for LAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format. • Direction: Select this option to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL Router will periodically send routing information and accept routing information, and then incorporate them into routing table. IN only means the ADSL Router will only accept but will not send RIP packet. OUT only means the ADSL Router will only send but will not accept RIP packet. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
TD-W8951NB
150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide
28
Figure 4-11
¾
Router Local IP:
These are the IP settings of the LAN interface for the device. These settings
may be referred to as Private settings. You may change the LAN IP address if needed. The
LAN IP address is private to your internal network and cannot be seen on the Internet.
•
IP Address:
Enter the Router’s local IP Address, then you can access to the Web-based
Utility via the IP Address, the default value is 192.168.1.1.
•
IP Subnet Mask:
Enter the Router’s Subnet Mask, the default value is 255.255.255.0.
•
Dynamic Route:
Select this option to specify the RIP (Routing Information protocol)
version for LAN interface, including
RIP1
,
RIP2-B
and
RIP2-M
. RIP2-B and RIP2-M are
both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B
using Broadcast format.
•
Direction:
Select this option to specify the RIP direction.
None
is for disabling the RIP
function.
Both
means the ADSL Router will periodically send routing information and
accept routing information, and then incorporate them into routing table.
IN only
means
the ADSL Router will only accept but will not send RIP packet.
OUT only
means the
ADSL Router will only send but will not accept RIP packet.