Toshiba 42HP95 Owner's Manual - English - Page 21

Connecting a digital audio system, Connecting an analog audio system - module

Page 21 highlights

Chapter 2: Connecting your TV Connecting a digital audio system The TV's DIGITAL AUDIO OUT terminal outputs a Dolby Digital or 2-channel down-mixed PCM (pulse-code modulation) signal for use with an external Dolby Digital decoder or other external audio system with optical audio input. You will need: one optical audio cable (Use an optical audio cable that has the larger "TosLink" connector and not the smaller "mini-optical" connector.) To control the audio: Turn on the TV and the digital audio device. Press MENU on the TV's remote control and open the AUDIO menu. Highlight Audio Setup and press ENTER. In the Optical Output Format field, select either Dolby Digital or PCM, depending on your device (see "Selecting the optical audio output format" on page 88). Audio Audio Settings Advanced Audio Settings Audio Setup Audio Setup MTS Language Speakers Optical Output Format Reset Stereo English On Dolby Digital Done Turn off the TV's built-in speakers in the same Audio Setup menu (above). Also see "Turning off the built-in speakers" on page 88. Connecting an analog audio system Dolby Digital decoder or other digital audio system LINE IN LR Optical Audio IN TV back panel Note: • Some audio systems may not be compatible with Dolby Digital bitstream signals. Older audio systems that are not compatible with standard optical out signals may not work properly, creating a high noise level that may damage speakers or headphones. THIS DAMAGE IS NOT COVERED BY YOUR WARRANTY. • The DIGITAL AUDIO OUT terminal outputs signals only when receiving digital broadcasts with the TV in single-window mode. • The DIGITAL AUDIO OUT terminal may not output some digital audio sources because of copy restrictions. This connection allows you to use external speakers with an external audio amplifier to adjust the sound level. You will need: one pair of standard audio cables To control the audio: Turn on the TV and the stereo amplifier. Turn off the TV's built-in speakers (see "Turning off the built-in speakers" on page 88). Note: To hear sound when using an external audio amplifier, the volume of both the TV and the amplifier must be set to a reasonable listening level. Analog audio amplifier LINE IN LR TV back panel Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. #01E_013-027_4250HP95 21 Black (E) 42/50HP95 *web 213:276 05.9.12, 10:06 PM 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114

21
Chapter 2: Connecting your TV
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.
(E) 42/50HP95 *web 213:276
Connecting a digital audio system
This connection allows you to use external speakers with an
external audio amplifier to adjust the sound level.
You will need:
²
one pair of standard audio cables
To control the audio:
Turn on the TV and the stereo amplifier.
Turn off the TV
s built-in speakers (see
Turning off the built-in
speakers
on page 88).
Note:
To hear sound when using an external audio amplifier,
the volume of both the TV and the amplifier must be set to a
reasonable listening level.
Analog audio amplifier
Connecting an analog audio system
The TV
s DIGITAL AUDIO OUT terminal outputs a Dolby
Digital
or 2-channel down-mixed PCM (pulse-code
modulation) signal for use with an external Dolby Digital
decoder or other external audio system with optical audio input.
You will need:
²
one optical audio cable (Use an optical audio cable that has
the larger
TosLink
connector and not the smaller
mini-optical
connector.)
To control the audio:
Turn on the TV and the digital audio device.
Press MENU on the TV
s remote control and open the AUDIO
menu.
Highlight Audio Setup and press ENTER.
In the Optical Output Format field, select either Dolby Digital
or PCM, depending on your
device (see
Selecting the
optical audio output format
on page 88).
Audio Setup
MTS
Stereo
Language
English
Reset
Done
Speakers
On
Optical Output Format
Dolby Digital
Turn off the TV
s built-in speakers in the same Audio Setup
menu (above). Also see
Turning off the built-in speakers
on
page 88.
Dolby Digital decoder or
other digital audio system
Note:
Some audio systems may not be compatible with Dolby Digital bitstream
signals. Older audio systems that are not compatible with standard
optical out signals may not work properly, creating a high noise level that
may damage speakers or headphones. THIS DAMAGE IS NOT
COVERED BY YOUR WARRANTY.
The DIGITAL AUDIO OUT terminal outputs signals only when receiving
digital broadcasts with the TV in single-window mode.
The DIGITAL AUDIO OUT terminal may not output some digital audio
sources because of copy restrictions.
Audio Settings
Advanced Audio Settings
Audio Setup
Audio
LINE IN
Optical
Audio IN
L
R
LINE IN
L
R
TV back panel
TV back panel
#01E_013-027_4250HP95
05.9.12, 10:06 PM
21
Black