Toshiba 42HP95 Owner's Manual - English - Page 99
Locking video inputs, Blocking channels, Unlocking programs temporarily
View all Toshiba 42HP95 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 99 highlights
Chapter 9: Using the Locks menu Blocking channels Unlocking programs temporarily With the Channels Block feature, you can block specific channels. You will not be able to tune blocked channels unless you clear the setting first. To block channels: 1. Press MENU and highlight the Locks menu icon. 2. Press z to displays the PIN code entering screen. 3. Enter your four-digit PIN code and press ENTER (see page 97 for details). 4. Press z to highlight Channels Block and then press ENTER. Locks Enable Rating Blocking Off Edit Rating Limits Channels Block Input Lock Off Front Panel Lock Off Game Timer Off New PIN Code Navigate Select CH RTN Back EXIT Exit 5. Using the yz x • buttons, select the input for which you want to change the rating limits (ANT1, ANT2, or Cable Box, if connected) and press ENTER. A list of the channels available for that input will be displayed along with the call letters for each channel, if available. 6. Press yz to highlight the channel you want to block, then press ENTER, which puts an "×" in the box next to that channel. 7. Repeat step 6 for other channels you want to block. Channels Block 1 2 3 4 5 6 7 8 9 10 ANT 1 ANT 1 ANT 2 Cable Box Allow All Block All Cancel Done 8. Highlight Done and press ENTER. To unblock individual channels: In step 6 above, press yz to highlight the channel you want to unblock, and then press ENTER to remove the "×" from the box, and highlight Done, and then press ENTER. To block all channels at once: Highlight Block All in step 6 above, and then highlight Done, and press ENTER. To unblock all locked channels at once: Highlight Allow All in step 6 above , and then highlight Done, and press ENTER. Note: Channel blocking may not take effect if you have a cable box connected and use the cable box controls to change channels. Channels Block 1 2 3 4 5 6 7 8 9 10 ANT 1 ANT 1 ANT 2 Cable Box Allow All Block All Cancel Done If you try to watch a TV program that exceeds the rating limits you set, the TV enters program lock mode. You can either unlock the program temporarily or select a non-locked program to watch. To temporarily unlock the program: 1. Press MUTE. 2. Enter your four-digit PIN code and press ENTER. If the correct code is entered, the program lock mode is released and the normal picture appears. All locking is disabled Locks Active Enter PIN code to temporaily unblock. **** until the TV is turned Cancel Done off, and will be enabled when the TV is turned on again. Locking video inputs You can use the Input Lock feature to lock the video input sources (VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD-1, ColorStream HD-2, HDMI, PC) and channels 3 and 4. You will not be able to view the input sources or channels until you turn off the input lock. To lock the video inputs: 1. Press MENU and highlight the Locks menu icon. 2. Press z to display the PIN code entering screen. 3. Enter your four-digit PIN code and press ENTER. 4. Press z to highlight Input Lock and press •. 5. Press y or z to select the level of video input locking you prefer, as described below: Video: Locks VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD1/ HD2, HDMI and PC. Video+: Locks VIDEO 1, VIDEO 2, VIDEO 3, Locks Enable Rating Blocking Off Edit Rating Limits Channels Block Input Lock Off Front Panel Lock Off Game Timer Off New PIN Code Off Video Video + Navigate Select CH RTN Back EXIT Exit ColorStream HD1/HD2, HDMI, PC, and channels 3 and 4. Select Video+ if you use the antenna terminal to play a video tape. Note: Make sure the POP is not on channel 3 or 4. Off: Unlocks all video input sources. 6. Press ENTER. Note: When a CableCARD™ is inserted, Video+ will behave the same as Video lock. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 99 #01E_097-100_4250HP95 99 Black (E) 42/50HP95 *web 213:276 05.9.12, 10:11 PM