ViewSonic LS625W - 3200 Lumens WXGA Short Throw Laser Projector with HV Keystone - Page 16

System, Remote Control Code, If you want to switch the code at the remote control end

Page 16 highlights

Remote control code The projector is capable of having 8 different remote control codes (1 to 8). When using multiple projectors close to each other at the same time, switching the remote control codes will prevent projector disruption by other remote controls. First set the projector's remote control code then switch the code of the remote control itself. If you want to switch the code at the projector end, please go to System: Remote Control Code menu and select 1 to 8. If you want to switch the code at the remote control end, please press and hold both the [ID set] and number key corresponding to the remote control code for at least 5 seconds. 1 is the initial code by default. Setting the code to 8 allows the remote control to control every projector. On Off COMP HDMI 1 HDMI 2 Auto Sync Source Aspect Freeze Pattern Blank PgUp PgDn 9 0 Color Mode Network PgUp PgDn 9 0 Color Mode Network The projector will not respond to commands issued by the remote control commands if the projector and remote control codes are not the same. When this happens, a message will appear to remind you to switch the remote control code. Remote control setting Remote control code 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84

9
Remote control code
The projector is capable of having 8 different remote control codes (1 to 8). When using
multiple projectors close to each other at the same time, switching the remote control
codes will prevent projector disruption by other remote controls. First set the projector’s
remote control code then switch the code of the remote control itself.
If you want to switch the code at the projector end, please go to
System:
Remote Control Code
menu and select 1 to 8.
If you want to switch the code at the remote control end,
please press and hold both the [ID set] and number key
corresponding to the remote control code for at least 5
seconds. 1 is the initial code by default. Setting the code to 8
allows the remote control to control every projector.
Pattern
Aspect
PgUp
PgDn
Freeze
Blank
On
Off
HDMI 1
HDMI 2
COMP
Source
Auto
Sync
Color
Mode
Network
9
0
PgUp
PgDn
Color
Mode
Network
9
0
The projector will not respond to commands issued by the remote control commands if the
projector and remote control codes are not the same. When this happens, a message will
appear to remind you to switch the remote control code.
Remote control setting
Remote control code