ViewSonic LS625W - 3200 Lumens WXGA Short Throw Laser Projector with HV Keystone - Page 50

Using the projector under standby mode, Support PJLink™, SNMP, AMX and Xpanel formats

Get ViewSonic LS625W - 3200 Lumens WXGA Short Throw Laser Projector with HV Keystone PDF manuals and user guides View all ViewSonic LS625W - 3200 Lumens WXGA Short Throw Laser Projector with HV Keystone manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

4. Press "Contact IT Help" button, and then a HELP DESK window will be displayed in the upper right corner of the screen. You can send information to the RoomView™ software administrator / user connected to the same local area network. For details, please access http: // www.crestron.com and www.crestron.com/ getroomview. **Crestron RoomView On the "Edit Room" page, input the IP address (or the host name) as the content displayed in the screen display menu of the projector, and input "02" as the IPID, and input "41794" as the reserved Crestron control port. Regarding the Crestron RoomView™ settings and command method, please access the following website to obtain the RoomView™ User Guid and more information: http://www.crestron.com/products/roomview_connected_embedded_projectors_ devices/resources.asp Support PJLink™, SNMP, AMX and Xpanel formats This projector is compatible with PJLink™, SNMP V.1, AMX or Xpanel V1.10. For details, please respectively refer to the User Guide or access the website to control and manage the projector. Using the projector under standby mode A number of projector functions can be used under Standby Mode (plugged in to power but not switched on). To use those functions, please confirm the cables and wires have been correctly connected. Refer to the chapter on cable connections for more information on cable connections. Active VGA Out After the COMPUTER 1 and COMPUTER OUT jacks are correctly connected to the equipment, select Power Management > Standby Settings > Active VGA Out > On to output the VGA signal. The projector only outputs the signal received by COMPUTER 1. LAN control Setting in the Advanced > Network Settings > Standby LAN control menu drives the projector to provide network functions in the standby mode. For details, please refer to "Control the projector through the local area network". 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
43
4.
Press “Contact IT Help” button, and then a HELP DESK window will be displayed in
the upper right corner of the screen. You can send information to the RoomView™
software administrator / user connected to the same local area network.
For details, please access http: // www.crestron.com and www.crestron.com/
getroomview.
**Crestron RoomView
On the “Edit Room” page, input the IP address (or the host name) as the content
displayed in the screen display menu of the projector, and input “02” as the IPID, and
input “41794” as the reserved Crestron control port.
Regarding the Crestron RoomView™ settings and command method, please access
the following website to obtain the RoomView™ User Guid and more information:
devices/resources.asp
Support PJLink™, SNMP, AMX and Xpanel formats
This projector is compatible with PJLink™, SNMP V.1, AMX or Xpanel V1.10. For
details, please respectively refer to the User Guide or access the website to control
and manage the projector.
Using the projector under standby mode
A number of projector functions can be used under Standby Mode (plugged in to
power but not switched on). To use those functions, please confirm the cables and
wires have been correctly connected. Refer to the chapter on cable connections for
more information on cable connections.
Active VGA Out
After the COMPUTER 1 and COMPUTER OUT jacks are correctly connected to the
equipment, select Power Management > Standby Settings > Active VGA Out > On to
output the VGA signal. The projector only outputs the signal received by COMPUTER
1.
LAN control
Setting in the Advanced > Network Settings > Standby LAN control menu drives the
projector to provide network functions in the standby mode. For details, please refer
to “Control the projector through the local area network”.