Vtech VH6212 User Manual - Page 31

Appendix, Registering Headset to Dongle

Get Vtech VH6212 PDF manuals and user guides View all Vtech VH6212 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Appendix Registering Headset to Dongle Register your Headset to the Dongle The VH6212 headset comes pre-registered to the Dongle. If, for some reason, the headset is not registered to the Dongle, follow the instructions below to register your headset to the Dongle. 1. Make sure the battery is properly installed in the headset. The headset LED light flashes slowly in red and blue to indicate the headset is not registered. 2. Place the headset in the charger cradle and allow it to charge for at least one hour before beginning registration. 3. Remove the headset from the charger cradle. 4. Press and hold the pair button on the Dongle for about four seconds until the Dongle LED light on flashes red very quickly, and then release the button. 5. Return the headset to the charger cradle for registration. The headset LED light alternates quickly in red and blue. It takes about 60 seconds to complete the registration process. Once the headset is registered, the headset LED light turns red when the battery is low and being charged, or turns purple when the battery is well charged, or turns blue when the battery is fully charged. If the registration fails, you hear the voice prompt "Not registered" when you press the headset ON/OFF button on the headset, and the headset ON/OFF button light on the headset alternates slowly in red and blue. To reset the headset, remove it from the charger cradle and try the registration process again. NOTE • You cannot register a headset if another system headset is in use. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
26
Registering Headset to Dongle
Register your Headset to the Dongle
The VH6212 headset comes pre-registered to the Dongle. If, for
some reason, the headset is not registered to the Dongle, follow the
instructions below to register your headset to the Dongle.
1. Make sure the battery is properly installed in the headset. The
headset
LED
light flashes slowly in red and blue to indicate the
headset is not registered.
2. Place the headset in the charger cradle and allow it to charge for at
least one hour before beginning registration.
3. Remove the headset from the charger cradle.
4. Press and hold the pair button on the Dongle for about four
seconds until the Dongle LED light on flashes red very quickly, and
then release the button.
5. Return the headset to the charger cradle for registration. The
headset
LED
light
alternates quickly in red and blue.
It takes about 60 seconds to complete the registration process. Once
the headset is registered, the
headset
LED
light turns red when the
battery is low and being charged, or turns purple when the battery is
well charged, or turns blue when the battery is fully charged.
If the registration fails, you hear the voice prompt
"Not registered"
when you press
the
headset
ON/OFF
button on the headset, and
the headset
ON/OFF
button light on the headset alternates slowly in
red and blue.
To reset the headset, remove it from the charger cradle and try the
registration process again.
NOTE
•
You cannot register a headset if another system headset is in use.
Appendix