Vtech VH6212 User Manual - Page 48

California Energy Commission battery charging testing, instructions

Get Vtech VH6212 PDF manuals and user guides View all Vtech VH6212 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Appendix California Energy Commission battery charging testing instructions This cordless headset is set up to comply with the energy-conserving standards right out of the box. These instructions are intended for California Energy Commission (CEC) compliance testing only. When the CEC battery charging testing mode is activated, all headset functions, except battery charging, will be disabled. If you have registered the cordless headset to the VH6212 Dongle, below are the testing instructions. To activate the CEC battery charging testing mode: 1. Unplug the headset charger power adapter from the power outlet. Make sure the headset is plugged with charged battery before proceeding. 2. Press and hold the pair button on the Dongle for about 10 seconds until the Dongle LED light flashes quickly in red, and then release the button. 3. Immediately press the pair button again. The Dongle LED light will turn steady green for 3 seconds, and then turn off. 4. Immediately press the pair button once again. It takes up to one minute to complete the deregistration process. The LED light turns steady red when the deregistration process is successful. NOTE: When the headset fails to enter this mode, repeat all the steps mentioned above. To deactivate the CEC battery charging testing mode: • Register the headset back to the Dongle. If you have registered the cordless headset to a compatible VTech DECT cordless telephone, please refer to the respective user's manual for the activation and deactivation of CEC battery charging testing mode. If you have registered the cordless headset to a telephone base that does not have CEC battery charging testing mode, all telephone functions on the cordless headset, except battery charging, will be disabled. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
43
Appendix
California Energy Commission battery charging testing
instructions
This cordless headset is set up to comply with the energy-conserving standards right out of
the box. These instructions are intended for California Energy Commission (CEC) compliance
testing only. When the CEC battery charging testing mode is activated, all headset functions,
except battery charging, will be disabled.
If you have registered the cordless headset to the
VH6212
Dongle, below are the testing
instructions.
To activate the CEC battery charging testing mode:
1.
Unplug the headset charger power adapter from the power outlet. Make sure the
headset is plugged with charged battery before proceeding.
2.
Press and hold the pair button on the Dongle for about 10 seconds until the Dongle LED
light flashes quickly in red, and then release the button.
3.
Immediately press the pair button again. The Dongle LED light will turn steady green for 3
seconds, and then turn off.
4.
Immediately press the pair button once again.
It takes up to one minute to complete the deregistration process. The
LED light turns steady
red when the deregistration process is successful.
NOTE:
When the headset fails to enter this mode, repeat all the steps mentioned above.
To deactivate the CEC battery charging testing mode:
•
Register the headset back to the Dongle.
If you have registered the cordless headset to a compatible VTech DECT cordless telephone,
please refer to the respective user's manual for the activation and deactivation of CEC battery
charging testing mode.
If you have registered the cordless headset to a telephone base that does not have CEC
battery charging testing mode, all telephone functions on the cordless headset, except
battery charging, will be disabled.