Vtech vt2910 User Manual - Page 21

Basic Operations

Get Vtech vt2910 PDF manuals and user guides View all Vtech vt2910 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

BASIC OPERATIONS MAKING CALLS Extend the Antenna whenever you remove the Handset from the Base Unit cradle There are two ways to make a call: • Press LINE 1/FLASH or LINE 2/ FLASH and listen for dial tone. The LCD will display HANDSET ON 1 (or 2). Dial the phone number. OR • With the Handset OFF, dial the phone number. Then, press the desired LINE key. After a 2 second delay to access dial tone, the phone number you entered will automatically be dialed. NOTE: If you make a mistake while entering digits (with the Handset OFF), press and hold the INT.COM/DEL key. The LCD will begin to delete digits, one by one, until you release the key. If you want to delete ALL digits at once, press and hold the CONF/CLEAR key. All previously entered digits will be deleted, and the LCD will be blank. To end your call, press OFF, or return the Handset to the Base Unit cradle. To put a call on HOLD from the Handset: Press the HOLD/PAUSE key to place a call on HOLD. Press the appropriate LINE key to cancel HOLD and return to the conversation. If you are on LINE 1 and press LINE 2, LINE 1 will automatically go into HOLD mode. Press OFF to end your call with LINE 2, then press LINE 1 to return to your party on LINE 1. Otherwise, with LINE 1 on HOLD and LINE 2 active, press CONF/ CLEAR to enter CONFERENCE mode. If you are on LINE 2 and press LINE 1, LINE 2 will automatically go into HOLD mode. Press OFF to end your call with LINE 1, then press LINE 2 to return to your party on LINE 2. Otherwise, with LINE 2 on HOLD and LINE 1 active, press CONF/CLEAR to enter CONFERENCE mode. To end a 2-Line CONFERENCE, press OFF. NOTE: You cannot end a call when it is on HOLD. First, press the appropriate LINE key, then press OFF (or return the Handset to the Base Unit cradle). REDIAL Press the appropriate LINE key and listen for dial tone. Then press REDIAL. The most recent phone number you called will automatically be redialed. Similar to Making Calls above, you can also press REDIAL with the Handset OFF, and then press the desired LINE key. The VT 2910c will wait 2 seconds for a dial tone, and then REDIAL the last number you called. VT2910C EN MANU 21 21 12/16/99, 6:17 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
21
MAKING CALLS
Extend the Antenna whenever you
remove the Handset from the Base
Unit cradle
There are two ways to make a call:
•
Press
LINE 1/FLASH
or
LINE 2/
FLASH
and listen for dial tone.
The
LCD will display
HANDSET ON 1
(or
2
)
.
Dial the phone number.
OR
•
With the Handset OFF, dial the
phone number.
Then, press the
desired
LINE
key.
After a 2 second
delay to access dial tone, the phone
number you entered will automatically
be dialed.
NOTE:
If you make a mistake while
entering digits (with the Handset OFF),
press and hold the
INT.COM/DEL
key.
The LCD will begin to delete digits, one
by one, until you release the key.
If you want to delete ALL digits at once,
press and hold the
CONF/CLEAR
key.
All previously entered digits will be deleted,
and the LCD will be blank.
To end your call, press
OFF
, or return
the Handset to the Base Unit cradle.
To put a call on HOLD from the
Handset:
Press the
HOLD/PAUSE
key to place
a call on HOLD.
Press the appropriate
LINE
key to cancel
HOLD and return to the conversation.
If you are on LINE 1 and press
LINE 2
,
LINE 1 will automatically go into HOLD
mode.
Press
OFF
to end your call with
LINE 2, then press
LINE 1
to return to your
party on LINE 1.
Otherwise, with LINE 1
on HOLD and LINE 2 active, press
CONF/
CLEAR
to enter CONFERENCE mode.
If you are on LINE 2 and press
LINE 1
,
LINE 2 will automatically go into HOLD
mode.
Press
OFF
to end your call with
LINE 1, then press
LINE 2
to return to
your party on LINE 2.
Otherwise, with
LINE 2 on HOLD and LINE 1 active,
press
CONF/CLEAR
to enter
CONFERENCE mode.
To end a 2-Line CONFERENCE, press
OFF
.
NOTE:
You
cannot
end a call when it is
on HOLD.
First, press the appropriate
LINE key, then press
OFF
(or return the
Handset to the Base Unit cradle).
REDIAL
Press the appropriate
LINE
key and listen
for dial tone.
Then press
REDIAL
.
The
most recent phone number you called will
automatically be redialed.
Similar to
Making Calls
above, you can
also press
REDIAL
with the Handset OFF,
and then press the desired
LINE
key.
The
VT 2910c
will wait 2 seconds for a dial
tone, and then REDIAL the last number
you called.
BASIC OPERATIONS
VT2910C EN MANU
12/16/99, 6:17 AM
21