Vtech vt2910 User Manual - Page 33

Your Base Unit and Handset may

Get Vtech vt2910 PDF manuals and user guides View all Vtech vt2910 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

IN CASE OF DIFFICULTY one of the other phones. YOUR CALLER FADES IN AND OUT. You may be nearly out of range. Move closer, or relocate the base. YOU HEAR OTHER CALLS WHILE USING YOUR PHONE. • Replace the Handset in the base cradle, wait a few moments and try again. • Disconnect your Base Unit from the telephone jack, and plug in a regular telephone. If you still hear other calls, the problem is probably in your wiring or local service. Call your local telephone company. YOU HEAR NOISE IN THE HANDSET, AND NONE OF THE KEYS OR BUTTONS WORK. • Make sure the power cord is plugged in. • Your Base Unit and Handset may not be operating on the same channel or security code. Place the Handset in the cradle for a few moments to reload the security code and reset the channel. COMMON CURE FOR ELECTRONIC EQUIPMENT Electronics, like people, can sometimes get confused. If the unit does not seem to be responding normally, then try putting the Handset in the cradle to reinitialize the unit. If it still does not seem to respond, perform the following steps (in the order listed): 1. Disconnect the power to the Base Unit. 2 Remove the Handset battery Pack 3. Wait a few minutes. 4. Connect power to the Base Unit. 5. Install the Handset battery pack. 6. Watch for the Handset to display " FOUND CHANNEL X". VT2910C EN MANU 33 33 12/16/99, 6:18 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
33
one of the other phones.
YOUR CALLER FADES IN AND OUT.
You may be nearly out of range. Move
closer, or relocate the base.
YOU HEAR OTHER CALLS WHILE
USING YOUR PHONE.
•
Replace the Handset in the base
cradle, wait a few moments and try
again.
•
Disconnect your Base Unit from the
telephone jack, and plug in a regular
telephone.
If you still hear other calls,
the problem is probably in your wiring
or local service.
Call your local
telephone company.
YOU HEAR NOISE IN THE HANDSET,
AND NONE OF THE KEYS OR
BUTTONS WORK.
•
Make sure the power cord is plugged
in.
•
Your Base Unit and Handset may not
be operating on the same channel
or security code.
Place the Handset
in the cradle for a few moments to
reload the security code and reset
the channel.
IN CASE OF DIFFICULTY
COMMON CURE
FOR ELECTRONIC
EQUIPMENT
Electronics, like people, can sometimes
get confused.
If the unit does not seem to
be responding normally, then try putting
the Handset in the cradle to reinitialize the
unit.
If it still does not seem to respond,
perform the following steps (in the order
listed):
1.
Disconnect the power to the Base
Unit.
2
Remove the Handset battery Pack
3.
Wait a few minutes.
4.
Connect power to the Base Unit.
5.
Install the Handset battery pack.
6.
Watch for the Handset to display
“
FOUND CHANNEL X
”.
VT2910C EN MANU
12/16/99, 6:18 AM
33