Weider Pro 9730 English Manual

Weider Pro 9730 Manual

Get Weider Pro 9730 PDF manuals and user guides View all Weider Pro 9730 manuals
Add to My Manuals
Save this manual to your list of manuals

Weider Pro 9730 manual content summary:

  • Weider Pro 9730 | English Manual - Page 1
    hot line will provide immediate assistance, free of charge to you. CUSTOMER HOT LINE: 1-800-999-3756 Mon.-Fri., 6 a.m.-6 p.m. MST CAUTION Read all precautions and instructions in this manual before using this equipment. Save this
  • Weider Pro 9730 | English Manual - Page 2
    PRECAUTIONS 3 BEFORE YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENT 22 TROUBLE-SHOOTING AND MAINTENANCE 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover Note: An EXPLODED DRAWING/PART LIST and a PART IDENTIFICATION CHART are attached to the center of this manual. Remove the EXPLODED DRAWING/PART
  • Weider Pro 9730 | English Manual - Page 3
    bar from the home gym system when performing an exercise that does not use the lat bar. 2. Read all instructions in this manual and in the accompanying literature before using the home gym system. 14. The home gym system is intended for home use only. Do not use the home gym system in a commercial
  • Weider Pro 9730 | English Manual - Page 4
    be found on a decal attached to the WEIDER® PRO 9730 (see the front cover of this manual). For your benefit, read this manual carefully before using the WEIDER® PRO 9730 Home Gym System. If you have additional questions, please call our Customer Service Department toll-free at 1-800-999- Before
  • Weider Pro 9730 | English Manual - Page 5
    and instructions: • Place all parts of the home gym system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. • The assembly is divided into four stages: 1) frame assembly, 2) press, squat, and butterfly arm assembly, 3) cable and
  • Weider Pro 9730 | English Manual - Page 6
    5/16" x 2 1/2" Carriage Bolts (1) in the Front Base (4). Hand tighten a 5/16" Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. 3 51 1 FRAME ASSEMBLY 42 65 3 4 1 6
  • Weider Pro 9730 | English Manual - Page 7
    Tube are resting in the pin grooves in the upper Weight. 25 6 Lubricate the insides of the holes in a Top Weight (76). Slide the Top Weight onto the Weight Guides (62) and set it on the stack of Weights (25). Assemble the other Weight Tube (63) and Top Weight (76) in the same manner. 63 63 76 25
  • Weider Pro 9730 | English Manual - Page 8
    and four 5/16" Nylon Locknuts (3). 7 11 11 27 55 88 27 49 44 27 27 3 44 3 56 Crossbar 42 FRAME ASSEMBLY 8. Attach the each set of the Weight Guides (62) to the Top Frame (55) with a 5/16" x 6" Bolt 8 (60), two 1/2" x 3/4" Spacers (61), and a 5/16" Nylon Locknut (3). Tighten all
  • Weider Pro 9730 | English Manual - Page 9
    Arm (48) with a 3/8" x 2.1/2" Bolt (7) and a 3/8" Nylon Locknut (21). 21 Attach a "V"-Pulley (6) and a Long Cable Trap (50) to the Left Arm (47) with a 3/8" x 2.1/2" Bolt (7) and a 3/8" Nylon Locknut (21). 48 ARM ASSEMBLY 12. Lubricate both axles on the Top Frame (55). Slide the Right Arm
  • Weider Pro 9730 | English Manual - Page 10
    42 85 Lubricate ARM ASSEMBLY CABLE ASSEMBLY 14. During steps 15 through 39, refer to the CABLE DIAGRAMS on pages 26 and 27 of 14 this manual to verify proper cable routing. Before beginning this section, identify the High Cable (23), the Low Cable (86), the Rear Cable (95), and the Press
  • Weider Pro 9730 | English Manual - Page 11
    on the Front Upright (42) with a 3/8" x 2 1/2" Bolt (7) and a 3/8" Nylon Locknut (21). Be sure that the Long Cable Trap is positioned to hold the Cable in place. 7 6 50 23 CABLE ASSEMBLY 17. Route the High Cable (23) around the "V"Pulley (6) on the Left Arm (47). Be sure that 17 the
  • Weider Pro 9730 | English Manual - Page 12
    of the 20 3 1/2" Pulleys (15) attached to the "I" Plates (81). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. 23 15 81 CABLE ASSEMBLY 21. Wrap the High Cable (23) around a 3 1/2" 21 Pulley (15). Attach the Pulley to the Top Frame (55
  • Weider Pro 9730 | English Manual - Page 13
    Cable only a couple of turns, as shown in the inset drawing. 24. Locate the Press Cable (58). Attach the Press Cable Cable to pivot. Wrap the Press Cable (58) around a 3 1/2" Pulley (15). Attach the Pulley and a Cable should be threaded onto the end of the Cable so only a couple of threads are
  • Weider Pro 9730 | English Manual - Page 14
    3/8" Washer (9), the 5/8" x 9/16" Spacer (73), the 3 1/2" Low Pulley (88), and the 3/8" Nylon Locknut (21) are oriented as shown. CABLE ASSEMBLY 9 71 17 73 88 27. Locate the Low Cable (86). Slide the Low 27 Cable into place under the 3 1/2" Low Pulley (88). Be sure that the end of the
  • Weider Pro 9730 | English Manual - Page 15
    is routed around the "V"-Pulley as shown. 30 42 86 16 9 15 66 21 85 9 6 CABLE ASSEMBLY 31. Wrap the Low Cable (86) around a 3 1/2" Pulley (15). Attach the Pulley and a Cable Trap (66) to the Press Frame (17) with a 3/8" x 3 1/2" Bolt (16), a 3/8" Washer (9), and a 3/8" Nylon Locknut (21). Be
  • Weider Pro 9730 | English Manual - Page 16
    (15) attached to the "I"-Plates 81 (81). The Cable must be routed from the direction shown. 15 86 CABLE ASSEMBLY 34. Slide a 5/16" Washer (8) onto a 5/16" x 3" Bolt 34 (93). Insert the Bolt into the Front Base (4). Slide theend of the Press Cable (88) onto the Bolt. Fully tighten a 5/16
  • Weider Pro 9730 | English Manual - Page 17
    tion shown. 95 15 87 5 21 87 55 21 15 95 CABLE ASSEMBLY 39. Attach the Rear Cable (95) to a Small "U" Bracket (67) with a 1/4" of the Cable only a couple of turns, as shown in the inset drawing. 95 3 67 72 10 2 63 Attach the Small "U" Bracket (67) to the indicated Weight Tube (63
  • Weider Pro 9730 | English Manual - Page 18
    40. Attach the Small Backrest (80) to the Rear 40 Upright (56) with two 1/4" x 2 1/2" Screws (43) and two 1/4" Washers (10). SEAT ASSEMBLY 80 56 10 43 41. Press a 1 3/4" Square Inner Cap (44) into the Rear Seat Frame (77). Insert the 1/4" x 2 1/2" Carriage Bolt (91) into the center hole
  • Weider Pro 9730 | English Manual - Page 19
    (42) with two 1/4" x 2 1/2" Screws (43) and two 1/4" Washers (10). The Backrest must be oriented as shown. 43 10 41 42 Thick End SEAT ASSEMBLY 44. Press a 1 1/2" Square Inner Cap (32) into the Front Seat Frame (36). 44 Insert the 1/4" x 2 1/4" Carriage Bolt (38) into the center hole in
  • Weider Pro 9730 | English Manual - Page 20
    Upright with a 5/16" x 2 3/4" Carriage Bolt (14) and the Seat Knob (40). 45 Lubricate-33 35 32 46 36 3 29 8 3 40 36 42 14 Pin SEAT ASSEMBLY 47. Press 3/4" Round Inner Caps (34) into the ends of both Pad Tubes (28). 47 Insert one Pad Tube (28) into the Front Seat Frame
  • Weider Pro 9730 | English Manual - Page 21
    this manual. Before using the home gym system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight
  • Weider Pro 9730 | English Manual - Page 22
    ADJUSTMENT The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the
  • Weider Pro 9730 | English Manual - Page 23
    (52) to the Low Cable (86) with a Cable Clip (53). Attach the other end of the Chain to the Eyebolt (35) with a Cable Clip. Always remove the the 5/16" x 2 3/4" Carriage Bolt (14) and the Seat Knob (40). For some exercises, the Rear Seat Frame (77) must B be removed. Remove the Seat Knob (40) and
  • Weider Pro 9730 | English Manual - Page 24
    98 169 6 162 94 116 106 117 196 7 191 118 140 121 128 204 8 210 126 169 134 147 215 The actual resistance at each weight station may vary due to differences in individual weight plates, as well as friction between the cables, pulleys, and weight guides. 24
  • Weider Pro 9730 | English Manual - Page 25
    detergent. Do not use solvents. TIGHTENING THE CABLES 1 Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. Insert the Weight Pin (26) under one of the
  • Weider Pro 9730 | English Manual - Page 26
    the diagrams to be sure that the Cables have been assembled correctly. The starting and ending points of each Cable have been labeled. The numbers show the proper route for each Cable. IMPORTANT: If the Cables have not been correctly routed, the WEIDER PRO 9730 will not function properly and damage
  • Weider Pro 9730 | English Manual - Page 27
    High Cable (23) 5 7 8 2 High Pulley 1 43 Press Cable (58) 2 1 Rear Upright 6 Weight Stack 9 3 Long "U" Bracket 27
  • Weider Pro 9730 | English Manual - Page 28
    the following information: 1. The MODEL NUMBER of the product (WESY97300). 2. The NAME of the product (WEIDER® 9730 Home Gym System). 3. The SERIAL NUMBER of the product (see the front cover of this manual). 4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING at
  • Weider Pro 9730 | English Manual - Page 29
    THIS PART IDENTIFICATION CHART FROM THE MANUAL This chart is provided to help you identify the small parts used in assembly. Important: Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assembled. The number in
  • Weider Pro 9730 | English Manual - Page 30
    1/4" Nylon Locknut (2)-5 5/16" Nylon Jam Nut (84)-2 5/16" Nylon Locknut (3)-24 3/8" Nylon Locknut (21)-22 1/4" Washer (10)-11 5/16" Washer (8)-11 3/8" Washer (9)-7 1/4" x 2 1/4" Carriage Bolt (38)-1 1/4" x 2 1/2" Screw (43)-5 1/4" x 2 1/2" Carriage Bolt (91)-1 1/4" x 2 1/4" Screw (82)-1 5/16" x 2
  • Weider Pro 9730 | English Manual - Page 31
    x 2" Bolt (12)-4 3/8" x 2 1/2" Bolt (7)-3 5/16" x 2 1/4" Bolt (33)-1 5/16" x 2 1/2" Bolt (22)-6 3/8" x 3 1/4" Bolt (85)-2 1" x 7/8" Plastic Bushing (75)-2 1/2" x 3/4" Spacer (61)-4 5/16" x 3" Bolt (93)-2 Cable Clip (53)-3 3/8" x 3 1/2" Bolt (16)-2 3/8" x 3 3/4" Bolt (71)-5 1" Retainer (69)-4
  • Weider Pro 9730 | English Manual - Page 32
    1" Round Cover Cap (70)-6 1" Round Inner Cap (49)-6 3/4" Round Inner Cap (34)-4 5/16" x 2" Eyebolt (35)-1 1" Square Inner Cap (65)-1 1 3/4" Square Inner Cap (44)-7 2" Square Inner Cap (27)-6 2" Square Cover Cap (78)-2 1 1/2" Square Inner Cap (32)-2 1" x 2" Inner Cap (83)-2
  • Weider Pro 9730 | English Manual - Page 33
    REMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUAL 81
  • Weider Pro 9730 | English Manual - Page 34
    Lat Bar Top Frame Rear Upright Long "U"-Bracket Press Cable 3/8" x 8" Bolt 5/16" x 6" Bolt 1/2" x 3/4" Spacer Weight Guide Weight Tube Weight Tube Bumper 1" Square Inner Cap Cable Trap Small "U"-Bracket 5/16" x 5" Bolt 1" Retainer 1" Round Cover Cap 3/8" x 3 3/4" Bolt 5/16" x 1 3/4" Bolt 5/8" x 9/16
  • Weider Pro 9730 | English Manual - Page 35
    83 49 92 8 31 83 92 22 8 31 49 22 94 79 8 8 3 94 9 21 3 3 15 71 66 56 85 58 11 8 55 68 27 15 87 21 27 87 15 21 3 20 66 12 3 21 15 60 61 89 90 93 8 62 27 11 27 87 8 49 21 44 15 71 23 44 61 27 21 60 3 7 50 6 21 74 69 7 50 6 21 70 48 74 69 70 47 44 80
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you have
questions, or find there are miss-
ing or damaged parts, we will
guarantee you complete satisfac-
tion through direct assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WESY97300
Serial No.
(Write the serial number in the space
above for reference.)
PATENT PENDING
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
®
USER'S MANUAL
Serial Number Decal