Whirlpool WEG730H0DS Installation Guide - Page 13
Electronic Ignition System - lowes
View all Whirlpool WEG730H0DS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 13 highlights
4. If the rear of the range lifts more than ½" (1.3 cm) off the floor without resistance, stop tilting the range and lower it gently back to the floor. The range foot is not engaged in the anti-tip bracket. IMPORTANT: If there is a snapping or popping sound when lifting the range, the range may not be fully engaged in the bracket. Check to see if there are obstructions keeping the range from sliding to the wall or keeping the range foot from sliding into the bracket. Verify that the bracket is held securely in place by the mounting screws. 5. Slide the range forward, and verify that the anti-tip bracket is securely attached to the floor or wall. 6. Slide range back so the rear range foot is inserted into the slot of the anti-tip bracket. 7. Repeat steps 1 and 2 to ensure that the range foot is engaged in the anti-tip bracket. If the rear of the range lifts more than ½" (1.3 cm) off the floor without resistance, the anti-tip bracket may not be installed correctly. Do not operate the range without anti-tip bracket installed and engaged. Please reference the "Warranty" section of the User Guide to contact service. 8. Move the range into its final location. Check that the range is level by placing a level on the oven bottom. See the "Level Range" section. IMPORTANT: If the range is moved to adjust the leveling legs, verify that the anti-tip bracket is engaged by repeating steps 1-8. Electronic Ignition System Initial lighting and gas flame adjustments Cooktop and oven burners use electronic igniters in place of standing pilots. When the cooktop control knob is turned to the ignite position, the system creates a spark to light the burner. All cooktop burners will spark, but only the burner with the control knob turned to the ignite position will produce a flame. This sparking continues as long as the control knob is turned to the ignite position. When the oven control is turned to the desired setting, sparking occurs and ignites the gas. Check Operation of Cooktop Burners Standard Surface Burners Push in and turn each control knob to the ignite position. The flame should light within 4 seconds. The first time a burner is lit, it may take longer than 4 seconds to light because of air in the gas line. If burners do not light properly: ■ Turn cooktop control knob to the off position. ■ Check that the range is plugged into a grounded 3 prong outlet. Check that the circuit breaker has not tripped or the household fuse has not blown. ■ Check that the gas shutoff valves are set to the open position. ■ Check that burner caps are properly positioned on burner bases. Repeat start-up. If a burner does not light at this point, turn the control knobs to the off position and contact your dealer or authorized service company for assistance. Please reference the "Warranty" section of the User Guide to contact service If the cooktop "low" burner flame needs to be adjusted for any of the burners, see the "Adjust Flame Height" section. Check Operation of Oven Bake Burner 1. Press BAKE. 2. Press the start pad. The oven burner should light within 8 seconds. The first time a burner is lit, it may take longer than 8 seconds to light because of air in the gas line. 3. After 2 minutes, open the oven door and check that the oven is warm. If burner does not light properly: ■ Press the off pad. ■ Check that the range is plugged into a grounded 3 prong outlet. Check that the circuit breaker has not tripped or the household fuse has not blown. ■ Check that the gas shutoff valves are set to the open position. Repeat steps 1-3. If the burner does not light at this point, press the off pad and contact your dealer or authorized service company for assistance. Please reference the "Warranty" section of the User Guide to contact service If the bake burner flame needs to be adjusted, see the "Adjust Flame Height" section. Refer to the User Guide for proper operation of the oven controls. Check Operation of Oven Broil Burner 1. Close the oven door. 1. Press BROIL. 2. Press the start pad. The oven burner should light within 8 seconds. The first time a burner is lit, it may take longer than 8 seconds to light because of air in the gas line. 3. After 2 minutes, open the oven door and check that the oven is warm. If burner does not light properly: ■ Press the off pad. ■ Check that the range is plugged into a grounded 3 prong outlet. Check that the circuit breaker has not tripped or the household fuse has not blown. ■ Check that the gas shutoff valves are set to the open position. Repeat steps 1-3. If the burner does not light at this point, press the off pad and contact your dealer or authorized service company for assistance. Please reference the "Warranty" section of the User Guide to contact service If the broil burner flame needs to be adjusted, see the "Adjust Flame Height" section. Refer to the User Guide for proper operation of the oven controls. 13