Whirlpool WEG730H0DS Installation Guide - Page 18

To Convert Oven Bake Burner Natural Gas to LP Gas, To Convert Oven Broil Burner Natural Gas to LP

Get Whirlpool WEG730H0DS PDF manuals and user guides View all Whirlpool WEG730H0DS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

To Convert Oven Bake Burner (Natural Gas to LP Gas) 1. Remove the oven racks and the oven door. See the "Oven Door" section. 2. Remove 2 screws and washers at the rear of the oven bottom. 3. Lift the rear of the oven bottom up and back until the front of the panel is away from the front frame. Remove from oven and set it aside on a covered surface. A 7. Replace the "47" spud with a "56" spud. Install the LP gas bake burner orifice spud, turning it clockwise until snug. IMPORTANT: Do not overtighten. A B A. Screws B. Oven bottom 4. Remove 2 screws from the bake burner. 5. Slide the front of the bake burner to the side to remove tab from front of oven. Lift the back of the bake burner off the oven orifice, and set the bake burner aside. Do not disconnect the wire. A B A. Bake burner B. Screws A. Orifice spud 8. Position the back of the bake burner over the oven orifice, and align the holes for the screws. 9. Reattach the bake burner with 2 screws. 10. Position the front of the oven bottom panel toward the front frame and lower the rear of the oven bottom panel into the oven. 11. Reattach the oven bottom panel with 2 screws and 2 washers. To Convert Oven Broil Burner (Natural Gas to LP Gas) 1. Remove the 1 screw from the broil burner. 2. Remove the flame spreader. 3. Remove the broil burner from the broil burner orifice hood. NOTE: The broil burner will hang in the back of the oven while you are changing the orifice hood. A A C B A. Oven orifice 6. Apply masking tape to the end of a ³⁄₈" (1 cm) nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning the Natural gas bake burner orifice spud counterclockwise to remove. The spud will be stamped with a "47." D A. Broil burner B. Flame spreader C. Screws D. Orifice hood 4. Apply masking tape to the end of a ³⁄₈" (1 cm) nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning the Natural gas broil burner orifice hood counterclockwise to remove. The hood will be stamped with a "155." 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
18
To Convert Oven Bake Burner (Natural Gas to LP Gas)
1.
Remove the oven racks and the oven door. See the “Oven
Door” section.
2.
Remove 2 screws and washers at the rear of the oven
bottom.
3.
Lift the rear of the oven bottom up and back until the front of
the panel is away from the front frame. Remove from oven
and set it aside on a covered surface.
4.
Remove 2 screws from the bake burner.
5.
Slide the front of the bake burner to the side to remove tab
from front of oven. Lift the back of the bake burner off the
oven orifice, and set the bake burner aside. Do not
disconnect the wire.
6.
Apply masking tape to the end of a
³⁄₈
" (1 cm) nut driver to
help hold the gas orifice spud in the nut driver while changing
it. Press nut driver down onto the gas orifice spud and
remove by turning the Natural gas bake burner orifice spud
counterclockwise to remove. The spud will be stamped with a
“47.”
7.
Replace the “47” spud with a “56” spud. Install the LP gas
bake burner orifice spud, turning it clockwise until snug.
IMPORTANT:
Do not overtighten.
8.
Position the back of the bake burner over the oven orifice,
and align the holes for the screws.
9.
Reattach the bake burner with 2 screws.
10.
Position the front of the oven bottom panel toward the front
frame and lower the rear of the oven bottom panel into the
oven.
11.
Reattach the oven bottom panel with 2 screws and
2 washers.
To Convert Oven Broil Burner (Natural Gas to LP Gas)
1.
Remove the 1 screw from the broil burner.
2.
Remove the flame spreader.
3.
Remove the broil burner from the broil burner orifice hood.
NOTE:
The broil burner will hang in the back of the oven while
you are changing the orifice hood.
4.
Apply masking tape to the end of a
³⁄₈
" (1 cm) nut driver to
help hold the gas orifice spud in the nut driver while changing
it. Press nut driver down onto the gas orifice spud and
remove by turning the Natural gas broil burner orifice hood
counterclockwise to remove. The hood will be stamped with
a “155.”
A. Screws
B. Oven bottom
A. Bake burner
B. Screws
A. Oven orifice
A
B
A
B
A
A. Orifice spud
A. Broil burner
B. Flame spreader
C. Screws
D. Orifice hood
A
C
D
A
B