Yamaha DRX-1 Owner's Manual - Page 32

If a timer recording is incorrect

Get Yamaha DRX-1 PDF manuals and user guides View all Yamaha DRX-1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

16 If you make a mistake, go back with t (left cursor) and re-enter the information. 17 Confirm with ENTER/OK. ➤ When all information is correct, the data is stored in a timer block. 18 To end, press TIMER. 19 Make sure you inserted a disc without write protec- tion. If you inserted a write protected disc, recording will not occur. 20 Turn the Recorder to standby mode by pressing POWER (B/I). If a timer recording is incorrect The following messages may appear in the timer menu when you set a timer recording: Collision The Timer recording overlaps with another timer recording. Solution: ● Ignore by pressing TIMER again.The program with the earlier start time will record completely.Then the remainder of the later program will record. ● Edit one or both timer recordings. ● Delete one of the timer recordings. Please enter channel number The VCR Plus+ system does not recognize the TV channel. Solution: ● Select the required channel number with t/u (left/ right cursor). ● Press ENTER/OK to confirm. PlusCode number wrong You entered an incorrect PlusCode number. Solution: ● Enter the correct information or quit by pressing TIMER. Weekend programming - not possible Date was incorrectly entered. Daily programming can only be used for recordings from Mondays to Fridays. Memory full All the timer blocks are in use. Solution: ● Delete one of the Timer recordings. Clock not set-check Clock channel The clock is not set. Set it manually (See 'Time/Date Manually') or adjust the Clock channel (See 'Time/Date Automatic.') Data error Solution: ● Make sure all information is correct and complete. Checking or altering a Timer Recording 1 Press TIMER on the remote control. 2 Select 'Timer list' with w/v (down/up cursor). Timer VCR Plus+ system Timer programming Timer list To exit Press TIMER 3 Press u (right cursor). Timer Timer List Date Ch. 04/ 20 120 07/ 20 089 10/ 20 065 11/ 20 120 Rec Start End Mode 09 : 00 P M 08: 30 P M 07: 00 A M 0:900 P M 11:00PM S P + 09:30PM S P + 07:30AM S P + 11:00PM S P + Total record time 05: 30 To change Press > To exit Press TIMER 4 Select the timer recording you want to check or alter with w/v (down/up cursor). ➤ The selected timer recording will be highlighted in blue. 5 Press u (right cursor). 6 Select what you want to check or alter with t/u (left/ right cursor). 7 Alter data with w/v (down/up cursor) or with the digit buttons 0-9. 8 Press ENTER/OK to conform. 9 To end, press TIMER, repeatedly if necessary to remove the menus. 10 Turn the Recorder to standby mode by pressing POWER (B/I). 28 RECORDING

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
28
R
ECORDING
16
If you make a mistake, go back with
t
(left cursor) and
re-enter the information.
17
Confirm with
ENTER/OK
.
When all information is correct, the data is stored
in a timer block.
18
To end, press
TIMER
.
19
Make sure you inserted a disc without write protec-
tion. If you inserted a write protected disc, recording
will not occur.
20
Turn the Recorder to standby mode by pressing
POWER
(
B
/I).
If a timer recording is incorrect
The following messages may appear in the timer menu
when you set a timer recording:
Collision
The Timer recording overlaps with another timer
recording.
Solution:
●
Ignore by pressing
TIMER
again. The program with
the earlier start time will record completely. Then
the remainder of the later program will record.
●
Edit one or both timer recordings.
●
Delete one of the timer recordings.
Please enter channel number
The VCR Plus+ system does not recognize the TV channel.
Solution:
●
Select the required channel number with
t
/
u
(left/
right cursor).
●
Press
ENTER/OK
to confirm.
PlusCode number wrong
You entered an incorrect PlusCode number.
Solution:
●
Enter the correct information or quit by pressing
TIMER
.
Weekend programming - not possible
Date was incorrectly entered. Daily programming can only
be used for recordings from Mondays to Fridays.
Memory full
All the timer blocks are in use.
Solution:
●
Delete one of the Timer recordings.
Clock not set-check Clock channel
The clock is not set. Set it manually (See ‘Time/Date
Manually’) or adjust the Clock channel (See ‘Time/Date
Automatic.’)
Data error
Solution:
●
Make sure all information is correct and complete.
Checking or altering a Timer Recording
1
Press
TIMER
on the remote control.
2
Select ‘Timer list’ with
w
/
v
(down/up cursor).
3
Press
u
(right cursor).
4
Select the timer recording you want to check or alter
with
w
/
v
(down/up cursor).
The selected timer recording will be highlighted in
blue.
5
Press
u
(right cursor).
6
Select what you want to check or alter with
t
/
u
(left/
right cursor).
7
Alter data with
w
/
v
(down/up cursor) or with the
digit buttons
0-9
.
8
Press
ENTER/OK
to conform.
9
To end, press
TIMER
, repeatedly if necessary to
remove the menus.
10
Turn the Recorder to standby mode by pressing
POWER
(
B
/I).
Timer
To exit
Press TIMER
Timer programming
Timer list
VCR Plus
system
+
Timer
Timer List
Date
04
/
20
07
/
20
10
/
20
11
/
20
120
089
065
120
09: 00 P M
08: 30 P M
07: 00 A M
09
: 00 P M
11: 00 P M
09: 30 P M
07: 30 A M
11: 00 P M
SP
SP
SP
SP
Ch.
Start
End
Rec
Mode
Total record time 05: 30
To exit
Press TIMER
To change
Press
>
+
+
+
+