2008 Yamaha Motorsports RS Viking Professional Owners Manual - Page 58

2008 Yamaha Motorsports RS Viking Professional Manual

Get 2008 Yamaha Motorsports RS Viking Professional PDF manuals and user guides View all 2008 Yamaha Motorsports RS Viking Professional manuals

Page 58 highlights

Periodic maintenance 9. Rotate the secondary sliding sheave clockwise and push it so that it separates from the secondary fixed sheave. 1. Secondary sliding sheave 2. Secondary fixed sheave 10. Install the V-belt between the secondary sliding and fixed sheaves. 1. V-belt position adjusting bolt 2. Spacer V-belt position More than 1.5 mm (0.06 in) above the edge From 1.5 mm (0.06 in) above the edge to 0.5 mm (0.02 in) below the edge More than 0.5 mm (0.02 in) below the edge Adjustment Remove spacer 1. V-belt Not necessary (It is correct.) 11. Install the drive guard and close the shroud. ESU12580 Drive chain housing Add spacer EWS00430 WARNING The engine, oil tank, brake disc, and coolant hoses will be very hot after the engine has been run. Avoid contact while they are still hot with any part of your body or clothing during inspection or repair. To check the drive chain housing oil level 1. Place the snowmobile on a level surface. 2. Remove the rubber cap. 7. Tighten the V-belt position adjusting bolts. V-belt position adjusting bolt tightening torque: 10 Nm (1.0 m·kgf, 7.2 ft·lb) 8. Install the V-belt over the primary sheave assembly. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Periodic maintenance
52
7.
Tighten the V-belt position adjusting
bolts.
8.
Install the V-belt over the primary sheave
assembly.
9.
Rotate the secondary sliding sheave
clockwise and push it so that it separates
from the secondary fixed sheave.
10.
Install the V-belt between the secondary
sliding and fixed sheaves.
11. Install the drive guard and close the
shroud.
ESU12580
Drive chain housing
WARNING
EWS00430
The engine, oil tank, brake disc, and cool-
ant hoses will be very hot after the engine
has been run. Avoid contact while they are
still hot with any part of your body or cloth-
ing during inspection or repair.
To check the drive chain housing oil level
1.
Place the snowmobile on a level surface.
2.
Remove the rubber cap.
1.
V-belt position adjusting bolt
2. Spacer
V-belt position
Adjustment
More than 1.5 mm
(0.06 in) above the
edge
Remove spacer
From 1.5 mm (0.06 in)
above the edge to 0.5
mm (0.02 in) below
the edge
Not necessary (It is
correct.)
More than 0.5 mm
(0.02 in) below the
edge
Add spacer
V-belt position adjusting bolt tightening
torque:
10 Nm (1.0 m·kgf, 7.2 ft·lb)
1.
Secondary sliding sheave
2.
Secondary fixed sheave
1. V-belt