3Com 3CRWE915075 User Guide - Page 77

distributed around the central node in a point-multipoint, select 2X2 mode for a point-to-point link

Get 3Com 3CRWE915075 - AirConnect 9150 11n 2.4 GHz PoE Access Point PDF manuals and user guides
UPC - 662705537740
View all 3Com 3CRWE915075 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Antennas Used per Mode 73 In some modes, not all of the connectors are in use. The following table defines which external antenna connectors are used in which mode: Mode 2x3 2x2 1x1 Antennas Used A,B,C A,C A Note: When using 1x1 mode, either in WDS mode or in AP mode using the 3CWE591 Omni antenna, only connector A is active. This is the connector on the far right, looking at the AP with the 3Com logo facing you. No other connectors are active in this mode. When in WDS mode: ■ select 1X1 mode when peers are omni-directional, distributed around the central node in a point-multipoint link. ■ select 2X2 mode for a point-to-point link, using either the 3CWE596 or 3CW598 panel antenna. The antennas must both point in the same direction, with one antenna rotated 90 degrees, in order for MIMO to function correctly. Note: In 2x2 mode, the two outer connectors (A and C) are active. The connector in the middle (B) is not active and should not be used.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
Antennas Used per Mode
73
In some modes, not all of the connectors are in use.
The following table defines which external antenna connectors
are used in which mode:
Note: When using 1x1 mode, either in WDS mode or in AP mode
using the 3CWE591 Omni antenna, only connector A is active.
This is the connector on the far right, looking at the AP with the
3Com logo facing you. No other connectors are active in this
mode.
When in WDS mode:
■
select 1X1 mode when peers are omni-directional,
distributed around the central node in a point-multipoint
link.
■
select 2X2 mode for a point-to-point link, using either the
3CWE596 or 3CW598 panel antenna. The antennas must
both point in the same direction, with one antenna rotated
90 degrees, in order for MIMO to function correctly.
Note: In 2x2 mode, the two outer connectors (A and C) are
active. The connector in the middle (B) is not active and should
not be used.
Mode
Antennas Used
2x3
A,B,C
2x2
A,C
1x1
A