3Com 3CXFE575CT User Guide - Page 43

NEW ZEALAND, Automatic calls to different numbers shall be not less than 5 seconds apart.

Get 3Com 3CXFE575CT - MHz 10/100 Lan Card Bus PDF manuals and user guides
UPC - 662705312057
View all 3Com 3CXFE575CT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

NEW ZEALAND Not all phones connected to the phone port will respond to incoming ringing. Do not report this as a fault unless the same phone will not respond to ringing when connected to a standard phone socket. This equipment shall not be set up to make automatic calls to the Telecom 111 Emergency Services. The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular, higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom. In addition to satisfactory line conditions a modem can only work properly if: I It is compatible with the modem at the other end of the call and, I The application using the modem is compatible with the application at the other end of the call - e.g. accessing the Internet requires suitable software in addition to a modem. This equipment should not be used in a manner which could constitute a nuisance to other Telecom customers. Some parameters required for compliance with Telecom's PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set up to operate within the following limits for compliance with Telecom specifications: There shall be no more than 10 call attempts to the same number within any 30 minute period for a single manual call initiation The equipment shall go back on-hook for a period of not less than 30 seconds between the end of one call attempt and the beginning of the next. Automatic calls to different numbers shall be not less than 5 seconds apart. When used in the Auto-Answer mode, the S0 register must be set with a value between 2 and 5. This ensures: A person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network. Caller identification information (which occurs between the first and second ring cadence) is not destroyed. This equipment does not meet Telecom's impedance requirements. Performance limitations may occur when used in conjunction with some parts of the network. Telecom will accept no responsibility should difficulties arise in such circumstances. The code for Call Waiting disable is *52 on the Telecom New Zealand telephone network.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
N
EW
Z
EALAND
Not all phones connected to the phone port will respond to incoming ringing. Do not report this as a fault unless the same
phone will not respond to ringing when connected to a standard phone socket.
This equipment shall not be set up to make automatic calls to the Telecom 111 Emergency Services.
The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that
device under all operating conditions. In particular, higher speeds at which this modem is capable of operating depend on a
specific network implementation which is only one of many ways of delivering high quality voice telephony to customers.
Failure to operate should not be reported as a fault to Telecom.
In addition to satisfactory line conditions a modem can only work properly if:
■
It is compatible with the modem at the other end of the call and,
■
The application using the modem is compatible with the application at the other end of the call – e.g. accessing the Internet
requires suitable software in addition to a modem.
This equipment should not be used in a manner which could constitute a nuisance to other Telecom customers.
Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated
with this modem. The associated equipment shall be set up to operate within the following limits for compliance with Telecom
specifications:
There shall be no more than 10 call attempts to the same number within any 30 minute period for a single manual call
initiation
The equipment shall go back on-hook for a period of not less than 30 seconds between the end of one call attempt and the
beginning of the next.
Automatic calls to different numbers shall be not less than 5 seconds apart.
When used in the Auto-Answer mode, the S0 register must be set with a value between 2 and 5. This ensures:
A person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been
successfully switched through the network.
Caller identification information (which occurs between the first and second ring cadence) is not destroyed.
This equipment does not meet Telecom’s impedance requirements. Performance limitations may occur when used in
conjunction with some parts of the network. Telecom will accept no responsibility should difficulties arise in such
circumstances.
The code for Call Waiting disable is *52 on the Telecom New Zealand telephone network.