3Ware 9550SXU16MLB10 User Guide - Page 140

Cancelling a Rebuild and Restarting It with a Different Drive, Rebuild Unit, Enter, Remove Drive

Get 3Ware 9550SXU16MLB10 - Itec - 9550sxu-16ml Multi-lane Internal Sata Ii Hardware Raid Controller Integrat PDF manuals and user guides
UPC - 693494971613
View all 3Ware 9550SXU16MLB10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 140 highlights

Maintaining Units Figure 49. Select Available Drive to Replace Faulted Drive 3 Tab to the Rebuild Unit button and press Enter. 4 Navigate to and select the OK button to continue. You are returned to the main screen; "Rebuilding" appears next to the unit you selected. 5 Press F8 to save your changes and exit 3BM. The unit will begin rebuilding about ten minutes after the operating system finishes loading and the 3ware driver has loaded. Cancelling a Rebuild and Restarting It with a Different Drive When you start a rebuild from 3BM, you cannot cancel from within the 3BM interface; however you can cancel a rebuild from within 3DM by using the Remove Drive link on the Maintenance page. If you do not want to boot the operating system and launch 3DM, you can also cancel a rebuild by physically removing a drive, and installing another one that you want to use. Then when you start 3BM, the unit will appear as degraded and you can rebuild it, using the steps described under "Rebuilding Units through 3BM" on page 132. Note: If you want to pause the rebuild process through 3DM, you can do so by setting or changing the rebuild schedule on the Scheduling page. If you set a schedule for rebuilds that does not include the current time, the rebuild process will pause. 134 3ware 9000 Series Serial ATA RAID Controller User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Maintaining Units
134
3ware 9000 Series Serial ATA RAID Controller User Guide
Figure 49. Select Available Drive to Replace Faulted Drive
3
Tab
to the
Rebuild Unit
button and press
Enter
.
4
Navigate to and select the
OK
button to continue.
You are returned to the main screen; “Rebuilding” appears next to the unit
you selected.
5
Press
F8
to save your changes and exit 3BM
.
The unit will begin rebuilding about ten minutes after the operating
system finishes loading and the 3ware driver has loaded.
Cancelling a Rebuild and Restarting It with a Different
Drive
When you start a rebuild from 3BM, you cannot cancel from within the 3BM
interface; however you can cancel a rebuild from within 3DM by using the
Remove Drive
link on the Maintenance page.
If you do not want to boot the operating system and launch 3DM, you can also
cancel a rebuild by physically removing a drive, and installing another one
that you want to use. Then when you start 3BM, the unit will appear as
degraded and you can rebuild it, using the steps described under “Rebuilding
Units through 3BM” on page 132.
Note:
If you want to pause the rebuild process through 3DM, you
can do so by setting or changing the rebuild schedule on the
Scheduling page. If you set a schedule for rebuilds that does not
include the current time, the rebuild process will pause.