ASRock 4Core1333-Viiv User Manual - Page 31

Onboard Headers and Connectors

Get ASRock 4Core1333-Viiv PDF manuals and user guides View all ASRock 4Core1333-Viiv manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

2.11 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! FDD connector (33-pin FLOPPY1) (see p.11 No. 30) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Blue) (39-pin IDE1, see p.11 No. 10) PIN1 IDE1 connect the blue end connect the black end to the motherboard to the IDE devices 80-conductor ATA 66/100 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATAII Connectors These six Serial ATAII (SATAII) (SATAII_1 (Port0): see p.11, No. 16) connectors support SATA data (SATAII_2 (Port1): see p.11, No. 17) SATAII_5 (Port4) SATAII_1 (Port0) cables for internal storage (SATAII_3 (Port2): see p.11, No. 19) devices. The current SATAII (SATAII_4 (Port3): see p.11, No. 21) interface allows up to 3.0 Gb/s (SATAII_5 (Port4): see p.11, No. 15) SATAII_6 (Port5) SATAII_2 (Port1)data transfer rate. (SATAII_6 (Port5): see p.11, No. 22) SATAII_3 (Port2) SATAII_4 (Port3) SATAII_6 (Port5) connector can be used for internal storage device or be connected to eSATAII connector to support eSATAII device. Please read "eSATAII Interface Introduction" on page 38 for details about eSATAII and eSATAII installation procedures. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
31
31
31
31
31
2.11 Onboard Headers and Connectors
2.11 Onboard Headers and Connectors
2.11 Onboard Headers and Connectors
2.11 Onboard Headers and Connectors
2.11 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
FDD connector
(33-pin FLOPPY1)
(see p.11
No. 30)
Note:
Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.11
No. 10)
Note:
Please refer to the instruction of your IDE device vendor for the details.
Serial ATAII Connectors
These six Serial ATAII (SATAII)
(SATAII_1 (Port0): see
p.11, No. 16)
connectors support SATA data
(SATAII_2 (Port1): see
p.11, No. 17)
cables for internal storage
(SATAII_3 (Port2): see
p.11, No. 19)
devices. The current SATAII
(SATAII_4 (Port3): see
p.11, No. 21)
interface allows up to 3.0 Gb/s
(SATAII_5 (Port4): see
p.11, No. 15)
data transfer rate.
(SATAII_6 (Port5): see
p.11, No. 22)
SATAII_6 (Port5) connector can be used for internal storage device or
be connected to eSATAII connector to support eSATAII device. Please
read “eSATAII Interface Introduction” on page 38 for details about eSATAII
and eSATAII installation procedures.
FLOPPY
1
Pin
1
the red-striped side to Pin1
connect
the black end
to the IDE devices
connect the blue end
to the motherboard
80-conductor ATA 66/100 cable
I
D
E
1
PIN1
SATAII_1 (Port0)
SATAII_2 (Port1)
SATAII_5 (Port4)
SATAII_6 (Port5)
SATAII_3 (Port2)
SATAII_4 (Port3)